AIR CONDITIONING SYSTEM, Diagnostic DTC:B1413/13

DTC Code DTC Name
B1413/13 Evaporator Temperature Sensor Circuit

DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioner unit to detect the temperature of the air that has passed through the evaporator and is used to control the air conditioning. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the cooled air temperature that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1413/13 Open or short in No. 1 cooler thermistor circuit

  • No. 1 cooler thermistor

  • Air conditioning harness assembly

  • Air conditioning amplifier assembly

WIRING DIAGRAM

A000NEDE24
*a Air Conditioning Harness Assembly
*b No. 1 Cooler Thermistor
*c Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

Note


  • When the auxiliary battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization Click here.

  • Before disconnecting the cable form the negative (-) battery terminal or replacing the air conditioning amplifier assembly, record the last operation state of the air conditioning for each transmitter. After replacement, it is necessary to perform memory registration for each transmitter Click here.

PROCEDURE


  1. READ VALUE USING GTS (EVAPORATOR FIN THERMISTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Data List Click here.

    5. Check the value(s) by referring to the table below.

      Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Evaporator Fin Thermistor

      No. 1 cooler thermistor /

      Min.: -29.70°C (-21.46°F)

      Max.: 59.55°C (139.19°F)

      		 Actual evaporator temperature displayed -
      OK
      The display is as specified in the normal condition column.
      Result
      Result Proceed to
      NG A
      OK (When troubleshooting according to Problem Symptoms Table) B
      OK (When troubleshooting according to the DTC) C

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    A

  2. INSPECT NO. 1 COOLER THERMISTOR


    1. Remove the No. 1 cooler thermistor Click here.

    2. Inspect the No. 1 cooler thermistor Click here.


    NG

    REPLACE NO. 1 COOLER THERMISTOR Click here

    OK

  3. INSPECT AIR CONDITIONING HARNESS ASSEMBLY


    1. A000N4CE03
      Text in Illustration
      *1 Air Conditioning Harness Assembly
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)
      *b

      Front view of wire harness connector

      (to No. 1 cooler thermistor)

      Remove the air conditioning harness assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z1-11 (TEA) - 1 Always Below 1 Ω
      z1-12 (SGA) - 2 Always Below 1 Ω
      z1-11 (TEA) - Body ground Always 10 kΩ or higher
      z1-12 (SGA) - Body ground Always 10 kΩ or higher
      z1-11 (TEA) - z1-12 (SGA) Always 10 kΩ or higher

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPLACE AIR CONDITIONING HARNESS ASSEMBLY Click here