SLIDING ROOF HOUSING INSTALLATION

PROCEDURE


  1. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY


    1. Temporarily install the sliding roof housing sub-assembly with the 12 bolts (vehicle body side) and 8 nuts.

      A000V1E

    2. Tighten the 8 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Tighten the 12 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Tighten the 12 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      A000WCB
    5. A000XEAE01
      *1 Outer Side
      *2 Clip
      *3 Front Side

      Connect the 4 drain hoses.

      Note

      The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.

    6. A000XFY

      w/ Rear Seat Entertainment System:

      Attach the 2 clamps to connect the wire harness.

  2. INSTALL REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH


    1. Install the rear sliding roof housing mounting bracket LH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Attach the clamp to connect the curtain shield airbag wire harness.

  3. INSTALL REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

    Tech Tips

    Use the same procedure described for the LH side.

  4. INSTALL SLIDING ROOF PANEL PLATE


    1. Attach the 2 guides to install the 2 sliding roof panel plates with the 4 bolts.

  5. INSTALL FRONT SLIDING ROOF GARNISH

    A000Z2T

    1. Attach the 5 claws to install the front sliding roof garnish.

  6. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    1. A000ZKS

      Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.

    2. Perform a level check.

      A000W35E01
      *1 Even

      1. Check the difference in the level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass sub-assembly is fully closed.

        Standard
        Area Measurement
        A - A -2.0 to +1.0 mm (-0.079 to +0.039 in.)
        B - B -1.0 to +2.0 mm (-0.039 to +0.079 in.)
        C - C -1.5 to +1.5 mm (-0.059 to +0.059 in.)
        D - D -1.0 to +1.5 mm (-0.039 to +0.059 in.)

        Tech Tips

        "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

      2. Perform a gap check.

        Check the gap between the roof panel and roof glass.

        Note

        The gap must be even all around.

    3. A000ZKS

      Using a T25 "TORX" driver, tighten the 4 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  7. CHECK FOR WATER LEAKS


    1. After adjusting the sliding roof glass sub-assembly, check for water leaks.

    2. If there are any leaks, readjust the sliding roof glass sub-assembly.

  8. INSTALL SLIDING ROOF SIDE GARNISH LH

    A000X2S

    1. Attach the 5 claws to install the sliding roof side garnish LH.

  9. INSTALL SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL NO. 1 ROOF SIDE AIR DUCT LH (w/ Rear Cooler)

    A000ZTE

    1. Install the No. 1 roof side air duct LH with the 3 clips.

  11. INSTALL NO. 1 ROOF SIDE AIR DUCT RH (w/ Rear Cooler)

    Tech Tips

    Use the same procedure described for the LH side.

  12. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

    Click here

  13. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL ROOF HEADLINING ASSEMBLY (for Long Body)

    Click here

  15. INSTALL ROOF HEADLINING ASSEMBLY (for Standard Body)

    Click here

  16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  18. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  19. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  20. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  21. CHECK SRS WARNING LIGHT

    Click here