SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch ON (IG).

    3. Turn the tester on.

    4. Enter the following menus:


      1. Select: Body / Sliding Roof / Data List.

    5. According to the display on tester, read the "Data List".

      Sliding Roof
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Open Switch Sliding roof switch open signal/ON or OFF

      ON: OPEN switch is pressed

      OFF: OPEN switch is not pressed

      		 -
      Close Switch Sliding roof switch close signal/ON or OFF

      ON: CLOSE switch is pressed

      OFF: CLOSE switch is not pressed

      		 -
      Up Switch Sliding roof switch tilt up signal/ON or OFF

      ON: UP switch is pressed

      OFF: UP switch is not pressed

      		 -
      Down Switch Sliding roof switch tilt down signal/ON or OFF

      ON: DOWN switch is pressed

      OFF: DOWN switch is not pressed

      		 -
      Hall IC1 Status Hall IC1 status/NORMAL or LOCK

      NORMAL: Hall IC1 is normal

      LOCK: Hall IC1 is abnormal

      		 -
      Hall IC1 Pulse Hall IC1 signal/LO or HI

      LO: Hall IC1 output Lo

      HI: Hall IC1 output Hi

      		 -
      Hall IC2 Status Hall IC2 status/NORMAL or LOCK

      NORMAL: Hall IC2 is normal

      LOCK: Hall IC2 is abnormal

      		 -
      Hall IC2 Pulse Hall IC2 signal/LO or HI

      LO: Hall IC2 output Lo

      HI: Hall IC2 output Hi

      		 -
      Door Courtesy Driver door courtesy light switch signal/ON or OFF

      ON: Driver door is open

      OFF: Driver door is closed

      		 -
      Ignition (MPX) Power switch signal (MPX signal)/ON or OFF

      ON: Power switch ON (IG)

      OFF: Power switch OFF

      		 -
      Ignition (Direct Signal) Power switch signal/ON or OFF

      ON: Power switch ON (IG)

      OFF: Power switch OFF

      		 -
      Key Off Permission Key-off operation permit signal/ON or OFF

      ON: Driver door is not closed within 45 sec. after power switch is turned OFF

      OFF: Any status except "ON" status

      		 -
      Down Switch Failure(Current) Down switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof tilt down signal failure (Current)

      Not Fail: Sliding roof tilt down signal not fail (Current)

      		 -
      Up Switch Failure(Current) Up switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof tilt up signal failure (Current)

      Not Fail: Sliding roof tilt up signal not fail (Current)

      		 -
      Close Switch Failure(Current) Close switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof close signal failure (Current)

      Not Fail: Sliding roof close signal not fail (Current)

      		 -
      Open Switch Failure(Current) Open switch failure signal (Current)/Fail or Not Fail

      Fail: Sliding roof open signal failure (Current)

      Not Fail: Sliding roof open signal not fail (Current)

      		 -
      Down Switch Failure(Past) Down switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof tilt down signal failure (Past)

      Not Fail: Sliding roof tilt down signal not fail (Past)

      		 -
      Up Switch Failure(Past) Up switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof tilt up signal failure (Past)

      Not Fail: Sliding roof tilt up signal not fail (Past)

      		 -
      Close Switch Failure(Past) Close switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof close signal failure (Past)

      Not Fail: Sliding roof close signal not fail (Past)

      		 -
      Open Switch Failure(Past) Open switch failure signal (Past)/Fail or Not Fail

      Fail: Sliding roof open signal failure (Past)

      Not Fail: Sliding roof open signal not fail (Past)

      		 -
      #Code Number of trouble codes Number of trouble codes -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch ON (IG).

    3. Turn the tester on.

    4. Enter the following menus:


      1. Select: Body / Sliding Roof /Active Test.

    5. According to the display on tester, perform the "Active Test".

      Sliding Roof
      Tester Display Test Part Control Range Diagnostic Note

      Slide Roof

      (Slide Roof)

      		 Operate sliding roof SLIDE CLOSE/TILT UP

      CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs

      OFF: Sliding roof is not operating

      		 Be careful to avoid injuries as this test causes vehicle parts to move.

      Slide Roof

      (Slide Roof)

      		 Operate sliding roof SLIDE OPEN/TILT DOWN

      OPN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs

      OFF: Sliding roof is not operating

      		 Be careful to avoid injuries as this test causes vehicle parts to move.