FRONT DOOR BELT MOULDING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH


    1. for Type A:


      1. Install the front door belt moulding sub-assembly LH with the 6 screws.

        Tech Tips

        Install the screws in the order shown in the illustration.

      2. Tighten the 5 belt line screws indicated by the arrows in the illustration.

        A000TPPE10

    2. for Type B:


      1. Install the front door belt moulding sub-assembly LH with the 6 screws.

        Tech Tips

        Install the screws in the order shown in the illustration.

      2. Tighten the 3 belt line screws indicated by the arrows in the illustration.

        A000ZPHE05

    3. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new 4 mm waterproof rivet into the nose piece.

    4. Using the air riveter or hand riveter, install the rivet shown in the illustration.

      A000YN0

      Tech Tips


      • The rivet is for fixing the front door belt moulding in place.

      • If the rivet cannot be cut, pull it once and cut it.

      Note


      • A000YPVE58

        Do not pry the rivet with the riveter as this will cause damage to the riveter and mandrel.

        Text in Illustration
        *1 Riveter
        *2 Mandrel
        *a INCORRECT
        *b CORRECT
      • A000VNRE37

        Confirm that the rivets are seated properly against the front door outside moulding.

      • Do not tilt the riveter when installing the rivet to the front door outside moulding.

      • Do not leave any space between the rivet head and front door outside moulding.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT
      • A000Z60E34

        Do not leave any space between the front door outside moulding and front door panel. Firmly hold together the 2 items while installing the rivet.

        Text in Illustration
        *1 Riveter
        *a INCORRECT
        *b CORRECT

  2. INSTALL FRONT DOOR FRONT LOWER FRAME UPPER COVER LH


    1. Attach the 2 clips to install the front door front lower frame upper cover LH.

  3. INSTALL FRONT DOOR GLASS RUN LH

    Click here

  4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

    Click here

  5. INSTALL FRONT DOOR SERVICE HOLE COVER LH

    Click here

  6. INSTALL FRONT DOOR WINDOW FRONT FRAME MOULDING LH

    Click here

  7. INSTALL FRONT DOOR WEATHERSTRIP LH

    Click here

  8. INSTALL FRONT DOOR BELT MOULDING REAR END COVER LH

    Click here

  9. INSTALL DOOR FRAME GARNISH LH

    Click here

  10. INSTALL FRONT DOOR TRIM COVER LH

    Click here

  11. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP LH

    Click here

  12. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  13. INSTALL FRONT DOOR NO. 2 SERVICE HOLE COVER LH

    Click here

  14. INSTALL FRONT MULTIPLEX NETWORK DOOR ECU LH

    Click here

  15. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

  16. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL

    Click here

  17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

  18. CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  19. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  20. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  21. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  22. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here