REAR SEAT ASSEMBLY(for Ottoman) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH

    A000XCN

    1. Install the rear seat reclining adjuster assembly LH with the 4 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  2. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH

    A000W2I

    1. Install the rear seat reclining adjuster assembly RH with the 4 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connector.

  3. INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. A000Z7DE04

      Connect the air duct to the vehicle body.

    2. Install the rear No. 2 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A000Y3WE05
      Text in Illustration
      *1 Protruding Part

      w/ Center Seat:

      Connect the anchor part of the rear center seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear center seat outer belt assembly to overlap the protruding part of the anchor bracket.

  4. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. A000VMUE06

      Connect the air duct to the vehicle body.

    2. Install the rear No. 1 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  5. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY (w/ Center Seat)

    Click here

  6. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)


    1. A000Y9G

      Connect the 2 connectors.

    2. Install the rear seat center armrest assembly with the 2 bolts and nut.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A000VRV

      Attach the hook to the center seatback frame wire.

    4. Attach the 2 clips to install the rear seat armrest hole board.

    5. A000WRG

      While pressing the button, lower the rear center seat headrest assembly.

    6. Raise the rear seat center armrest assembly.

  7. INSTALL REAR SEATBACK ASSEMBLY LH

    A000U6KE02

    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the clip and attach the 3 pieces of fastening tape.

      Text in Illustration
      *1 Fastening Tape
    4. A000TG0

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A000UQB

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    7. A000VLQ

      Connect the rear seat 3 point type belt assembly LH to the rear seat shoulder belt guide LH.

    8. Attach the 2 claws to close the 2 caps.

    9. A000XVRE06
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

  8. INSTALL REAR SEATBACK ASSEMBLY RH

    A00105CE04

    1. Connect the rear seatback assembly RH to the rear No. 2 seat adjuster assembly, and press down on the rear seatback assembly RH to install it to the rear No. 2 seat adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH to the rear No. 2 seat adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Attach the clip and 3 pieces of fastening tape.

    4. Attach the 2 claws to connect the air hose.

      Text in Illustration
      *1 Air Hose
      *2 Fastening Tape
      *3 Air Duct

    5. Install the nut.

    6. A000WI1

      Connect the 3 connectors and attach the 6 wire harness clamps.

    7. A000TSV

      Connect the 3 connectors.

    8. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    9. A000W4H

      Install the rear seat 3 point type belt assembly RH to the rear seat shoulder belt guide RH.

    10. Attach the 2 claws to close the 2 caps.

    11. A000VQOE02
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly RH to overlap protruding parts of the floor panel.

  9. INSTALL REAR SEAT CONSOLE BOX (w/ Rear Console Box)

    Click here

  10. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)


    1. A000Z7H

      Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.

      Note

      Be careful not to damage the vehicle body.

    2. Attach the front hook of the rear center seat cushion assembly to the vehicle body.

  11. INSTALL REAR SEAT AIRBAG ASSEMBLY RH


    1. A000VNG

      Install the rear seat airbag assembly RH with the 3 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Connect the connector and attach the wire harness clamp.

  12. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A000WE5

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear seatback frame assembly LH.

      Note

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  13. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. Operate the ottoman switch to move the ottoman to the return position.

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A000VJLE02
      Text in Illustration
      *1 Seat Cover Hook
      *2 Nut
      *3 Rear Seat Cushion Lock Hook
      *4 Rear Hook

      Connect the connector.

    5. Attach the rear hook of the rear seat cushion assembly RH to the rear seatback spring assembly RH.

      Note

      Be careful not to damage the vehicle body.

    6. Attach the 2 front hooks of the rear seat cushion assembly RH to the the rear No. 1 seat adjuster assembly.

    7. Connect the 2 rear seat cushion lock hooks.

    8. Connect the seat cushion ottoman part with the 2 nuts.

    9. Install the 2 seat cushion cover hooks.

  14. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  16. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  17. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  18. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  19. CHECK SRS WARNING LIGHT

    Click here

  20. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here

  21. CHECK REAR SUNSHADE SYSTEM (w/ Center Seat)

    Click here

  22. CHECK REAR DOOR SUNSHADE SYSTEM (w/ Center Seat)

    Click here