REAR SEAT ASSEMBLY(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH


    1. A000XCN

      Install the rear seat reclining adjuster assembly LH with the 4 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  2. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  3. INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. A000Z7DE05

      Connect the air duct to the vehicle body.

    2. Install the rear No. 2 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A000Y3WE05
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear center seat outer belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear center seat outer belt to overlap the protruding part of the anchor bracket.

  4. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. A00103IE01

      Connect the air duct to the vehicle body.

    2. Install the rear No. 1 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  5. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. A000Y9G

      Connect the 2 connectors.

    2. Install the rear seat center armrest assembly with the 2 bolts and nut.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A000VRV

      Attach the hook to the center seatback frame wire.

    4. Attach the 2 clips to install the rear seat armrest hole board.

    5. A000WRG

      While pressing the button, lower the rear center seat headrest assembly.

    6. Raise the rear seat center armrest assembly.

  6. INSTALL REAR SEATBACK ASSEMBLY LH

    A000WLTE01

    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the clip and attach the 3 pieces of fastening tape.

      Text in Illustration
      *1 Fastening Tape
    4. A000TG0

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A000UQB

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    7. A000VLQ

      Connect the seat belt to the shoulder belt guide.

    8. Attach the 2 claws to close the 2 caps.

    9. A000XVRE06
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

  7. INSTALL REAR SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  8. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY

    A000Z7H

    1. Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.

      Note

      Be careful not to damage the vehicle body.

    2. Attach the front hook of the rear center seat cushion assembly to the vehicle body.

  9. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A000WE5

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

      Note

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  10. INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  13. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  14. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  15. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  16. CHECK SRS WARNING LIGHT

    Click here

  17. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here

  18. CHECK REAR SUNSHADE SYSTEM

    Click here

  19. CHECK REAR DOOR SUNSHADE SYSTEM

    Click here