REAR SEAT ASSEMBLY(for Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL HEADPHONE TERMINAL

    Click here

  2. INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


    1. Install the rear seat center armrest cup holder sub-assembly with the 2 screws.

  3. INSTALL REAR POWER SEAT SWITCH


    1. Install the rear power seat switch with the 4 screws.

  4. INSTALL REAR NO. 1 SEAT CENTER ARMREST PANEL


    1. Install the rear No. 1 seat center armrest panel to the rear seat armrest hole board with the 3 screws.

    2. Connect the 2 connectors.

    3. Attach the 3 guides and 8 claws to install the rear No. 1 seat center armrest panel together with the rear seat armrest hole board.

  5. INSTALL TELEVISION SWITCH AND VOLUME ASSEMBLY


    1. Install the television switch and volume assembly.

  6. INSTALL CENTER SEATBACK FRAME SUB-ASSEMBLY


    1. Install the center seatback frame sub-assembly to the rear center armrest assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Attach the wire harness clamp.

  7. INSTALL REAR SEAT ARMREST HOLE COVER


    1. Attach the 2 clips to install the rear seat armrest hole cover.

  8. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


    1. Install the rear center seat headrest assembly with the 2 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  9. INSTALL REAR CENTER SEAT CUSHION PAD


    1. Install the rear center seat cushion pad to the rear center seat cushion frame.

  10. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY


    1. Set the center seat cushion cover sub-assembly in place.

    2. Attach the fastening tape.

    3. Using hog ring pliers, install the center seat cushion cover to the center seat cushion pad with frame with 23 new hog rings.

      Note


      • Be careful not to damage the center seat cushion cover sub-assembly.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the center seat cushion cover sub-assembly.

      A000WVSE02
      Text in Illustration
      *1 Fastening Tape *2 Hog Ring Pliers

  11. INSTALL REAR SEAT CLIMATE CONTROL BLOWER LH


    1. A000Z2V

      Install the rear seat climate control blower LH with the 3 nuts.

    2. A000VX9

      Connect the connector.

  12. INSTALL AIR FILTER

    A000YO2

    1. Attach the 2 claws to install the air filter.

      Tech Tips

      Use the same procedure to install the air filter on the other side.

  13. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH


    1. A000TYU

      Attach the claws to connect the seat climate control controller LH.

    2. Install the 2 screws.

    3. A000V6Y

      Connect the 2 connectors and attach the 2 wire harness clamps.

    4. A000YUS

      Install a new rear No. 2 seat cushion pad.

  14. INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY LH

    A000V2H

    1. Install the rear seat belt inner anchor bracket assembly LH with the nut.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  15. INSTALL REAR SEAT INNER BELT ASSEMBLY LH

    Click here

  16. INSTALL REAR SEAT WIRE LH

    A000TLP

    1. Attach the 11 wire harness clamps to install the rear seat wire LH.

    2. Connect the 3 connectors.

  17. INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER LH

    A000VRDE02
    Text in Illustration
    *1 Felt Pad

    1. Install the rear seatback climate blower LH with the 2 screws.

    2. Install the 3 nuts.

    3. Connect the 3 connectors and attach the wire harness clamp.

    4. Install a new felt pad.

  18. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


    1. A000WITE01
      Text in Illustration
      *1 Hog Ring Pliers

      Set the separate type rear seatback cover LH in place.

    2. Using hog ring pliers, install the separate type rear seatback cover LH to the rear seatback pad LH with 10 new hog rings.

      Note


      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

  19. INSTALL REAR SEATBACK COVER WITH PAD LH


    1. Set the rear seatback cover with pad LH in place.

    2. Using hog ring pliers, install the rear seatback cover with pad LH to the rear seatback spring assembly LH with 19 new hog rings.

      Note


      • Be careful not to damage the rear seatback cover with pad LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad LH.

    3. Attach the 8 hooks.

    4. Connect the connector.

    5. Attach the seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }
      A000UR9E02
      Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
      *3 Hog Ring Pliers - -

  20. INSTALL REAR SEAT LOCK BASE LH


    1. A000ZHU

      Install the rear seat lock base LH with the 3 screws.

  21. INSTALL REAR SEAT COVER CAP LH


    1. A000WT9

      Attach the 5 claws to install the rear seat cover cap LH.

  22. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Attach the guide to install the seat heater control sub-assembly.

    2. Connect the connector.

      Tech Tips

      Use the same procedure to install the seat heater control sub-assembly on the other side.

  23. INSTALL REAR SEAT CLIMATE CONTROL ECU LH

    A000WNU

    1. Install the rear seat climate control ECU LH with the 2 nuts.

    2. Connect the 2 connectors.

  24. INSTALL POSITION CONTROL ECU ASSEMBLY

    A000USV

    1. Install the position control ECU assembly with the 2 nuts.

    2. Connect the 2 connectors.

      Tech Tips

      Use the same procedure to install the position control ECU assembly on the other side.

  25. INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    A000YLA

    1. Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly with the 2 bolts.

    2. Connect the 2 connectors and attach the wire harness clamp.

      Tech Tips

      Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.

  26. INSTALL REAR SEAT HEADREST SUPPORT

    A000Y18

    1. Attach the 4 claws to install the 2 rear seat headrest supports.

      Tech Tips

      Use the same procedure to install the rear seat headrest support on the other side.

  27. INSTALL REAR SEAT HEADREST ASSEMBLY

    A000TH2

    1. Install the rear seat headrest assembly with the 2 pins.

      Tech Tips

      Use the same procedure to install the rear seat headrest assembly on the other side.

  28. INSTALL REAR SEAT SHOULDER BELT GUIDE LH

    A000Y9J

    1. Install the rear seat shoulder belt guide LH with the 3 screws.

  29. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. A000Y0RE01
      Text in Illustration
      *1 Hog Ring Pliers

      Set the separate type rear seat cushion cover LH in place.

    2. Using hog ring pliers, install the separate type rear seat cushion cover LH to the rear seat cushion pad LH with 15 new hog rings.

      Note


      • Be careful not to damage the separate type rear seat cushion cover LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover LH.

  30. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY LH

    A000V8SE01
    Text in Illustration
    *1 Hog Ring Pliers

    1. Set the rear seat cushion spring assembly LH in place.

    2. Using hog ring pliers, install the rear seat cushion spring assembly LH to the rear seat cushion cover with pad LH with 22 new hog rings.

      Note


      • Be careful not to damage the rear seat cushion cover with pad LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seat cushion cover with pad LH.

  31. INSTALL REAR SEAT CLIMATE CONTROL BLOWER RH

    Tech Tips

    Use the same procedures described for the LH side.

  32. INSTALL SEAT CLIMATE CONTROL CONTROLLER RH

    Tech Tips

    Use the same procedures described for the LH side.

  33. INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  34. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY

    Click here

  35. INSTALL REAR SEAT INNER BELT ASSEMBLY RH

    Click here

  36. INSTALL REAR SEAT WIRE RH

    Tech Tips

    Use the same procedures described for the LH side.

  37. INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER RH

    Tech Tips

    Use the same procedures described for the LH side.

  38. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  39. INSTALL REAR SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedures described for the LH side.

  40. INSTALL REAR SEAT LOCK BASE RH

    Tech Tips

    Use the same procedures described for the LH side.

  41. INSTALL REAR SEAT COVER CAP RH

    Tech Tips

    Use the same procedures described for the LH side.

  42. INSTALL REAR SEAT CLIMATE CONTROL ECU RH

    Tech Tips

    Use the same procedures described for the LH side.

  43. INSTALL REAR SEAT SHOULDER BELT GUIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  44. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  45. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.