FRONT SEAT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

If the seat is set down in another location after removing it from the vehicle, the seat may tilt and damage the front seat adjuster assembly LH due to the difference in shape between the left and right seat tracks.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL FRONT SEAT WIRE LH


    1. Attach the 13 wire harness clamps to install the front seat wire LH.

    2. Connect the 4 connectors.

    3. Install the bolt.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }
      A000TNW

  2. INSTALL SEAT POSITION AIRBAG SENSOR

    Click here

  3. INSTALL SEAT CLIMATE CONTROL BLOWER LH

    A000WGL

    1. Install the climate control blower with the 2 bolts.

    2. Connect the connector and attach the wire harness clamps.

    3. Attach the 4 claws to connect the climate control duct.

  4. INSTALL NO. 1 AIR FILTER

    A000ZYO

    1. Rotate the air filter clockwise to attach the 4 claws to install it.

  5. INSTALL FRONT SEAT CLIMATE CONTROL ECU LH

    A000T9N

    1. Install the front seat climate control ECU LH with the 2 bolts.

    2. Connect the 2 connectors.

  6. INSTALL FRONT NO. 2 SEAT TRAVEL LINK

    A000UZY

    1. Install the front No. 2 seat travel link with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL FRONT NO. 1 SEAT TRAVEL LINK

    Tech Tips

    Use the same procedures described for the front No. 2 seat travel link.

  8. INSTALL NO. 1 SEAT CUSHION PLATE

    A000VDW

    1. Install the No. 1 seat cushion plate with the 2 bolts.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

  9. INSTALL FRONT SEAT CUSHION SPRING

    A000TRK

    1. Install the front seat cushion spring.

      Tech Tips

      Use the same procedure to install the front seat cushion spring on the other side.

  10. INSTALL FRONT SEAT LOWER CUSHION SHIELD

    A000ZR4

    1. Install the front seat lower cushion shield with the 4 nuts.

  11. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    A000WE4

    1. Attach the wire harness clamp.

    2. Install the reclining adjuster inside cover LH with the screw.

  12. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly LH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly LH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A000ZLQ
    3. A000W2W

      Install the 4 bolts.

  14. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (w/o Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly RH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly RH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A000Z3L
    3. A000W4R

      Install the 2 bolts.

  15. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (BACK SIDE)


    1. A000WDB

      Install the seat climate control controller LH with the 2 screws.

  16. INSTALL FRONT SEATBACK FRAME ASSEMBLY LH


    1. A000TBO

      Temporarily install the front seatback frame assembly LH with the 4 bolts.

    2. Push the front seatback frame assembly LH towards the rear, and tighten the 4 bolts.

      Torque:
      43 N*m  { 439 kgf*cm, 32 ft.*lbf }

    3. for Driver Side:


      1. A000W9S

        w/ Active Headrest:

        Attach the 9 clamps and connect the 4 connectors.

      2. A000ZUN

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 4 connectors.

    4. for Front Passenger Side:


      1. A000XL6

        w/ Active Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      2. A000UB5

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      3. A000V6L

        w/ Retractable Headrest:

        Attach the 7 clamps and connect the 2 connectors.

  17. INSTALL FRONT SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. w/ Active Headrest:


      1. A000U8W

        Attach the 2 claws.

      2. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      3. A000V4L

        Connect the connector and attach the 2 wire harness clamps.

    2. w/ Pre-crash Intelligent Headrest:


      1. A001057

        Attach the 2 claws to connect the connector to the connector holder.

      2. A000ZU7

        Attach the guide to install the plate.

      3. Install the screw.

      4. A000XPU

        Attach the 2 claws.

      5. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      6. Attach the 4 wire harness clamps.

      7. A000V4L

        Connect the connector and attach the 2 wire harness clamps.

    3. w/ Retractable Headrest:


      1. A000Y6H

        Install the headrest stay cover with the 2 screws.

      2. A000ZMF

        Attach the 2 claws to install the cable.

      3. A000YDL

        Attach the 2 claws to install the motor.

      4. A000YNS

        Attach the 2 claws to install the headrest adjuster.

      5. Install the 4 bolts and 2 screws.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  18. INSTALL FRONT SEAT HEADREST BRACKET (w/ Active Headrest)


    1. A000VAW

      Attach the wire harness clamp to install the front seat headrest bracket to the active headrest inflator.

  19. INSTALL ACTIVE HEADREST INFLATOR (w/ Active Headrest)

    Click here

  20. INSTALL FRONT NO. 5 SEAT SET BRACKET (w/ Shoulder Switch)


    1. A000YHT

      Attach the 2 clips to install the front No. 5 seat set bracket.

    2. Install the 2 screws.

  21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Set the separate type front seatback cover in place.

    2. for Sport Package:

      Attach the 4 pieces of fastening tape.

    3. Using hog ring pliers, install the separate type front seatback cover to the front seatback pad with 20 new hog rings as shown in the illustration.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      Tech Tips

      Install the hog rings at the cutouts.

      A000WIDE01
      Text in Illustration
      *A except Sport Package *B for Sport Package
      *1 Fastening Tape *2 Hog Ring Plier

  22. INSTALL FRONT SEATBACK COVER WITH PAD


    1. Set the front seatback cover with pad in place.

    2. A000YCK

      Attach the 9 hooks to install the front seatback cover with pad.

    3. Attach the 3 clips.

    4. A000ZAW

      Attach the front seatback cover bracket with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  23. INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. Connect the connector.

    2. A000YZF

      Attach the 2 claws to install the power seat switch assembly.

  24. INSTALL FRONT SEAT HEADREST SUPPORT

    A000TKI

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  25. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A000U3D

        Install the front seat headrest assembly with the 2 pins.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Install the front seat headrest assembly.

  26. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. Set the separate type front seat cushion cover in place.

    2. for Driver Side:


      1. A000WM0E01
        Text in Illustration
        *1 Hog Ring Pliers

        except Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A000U7QE01
        Text in Illustration
        *1 Hog Ring Pliers

        for Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion pad with 17 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      3. A000YRD

        Install the 2 clips.

    3. for Front Passenger Side:

      for Ottoman:


      1. A000YWOE01
        Text in Illustration
        *1 Hog Ring Pliers

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A000YH9

        Install the 2 clips.

    4. for Front Passenger Side:

      except Ottoman:


      1. A000TVZE01
        Text in Illustration
        *1 Hog Ring Pliers

        except Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A000XIKE01
        Text in Illustration
        *1 Hog Ring Pliers

        for Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 17 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      3. A000YH9

        Install the 2 clips.

  27. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH


    1. Attach the guide to install the seat heater control sub-assembly LH.

  28. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the front seat cushion cover with pad in place.

    2. for Driver Side:


      1. A000W1L

        Attach the 10 hooks to install the front seat cushion cover with pad.

      2. A000WLP

        Attach the fastening tape.

      3. A000TRH

        Install the 6 clips.

    3. for Front Passenger:

      for Ottoman:


      1. A000U58

        Attach the 10 hooks to install the front seat cushion cover with pad.

      2. A000WTF

        Attach the fastening tape.

      3. A000UFO

        Install the 6 clips.

    4. for Front Passenger:

      except Ottoman:


      1. A000XIP

        Attach the 8 hooks to install the front seat cushion cover with pad.

    5. Connect the seat heater connector.

    6. A000V0H

      Install the 2 clips.

  29. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (CUSHION SIDE)

    A000TRB

    1. Install the seat climate control controller LH with the 2 screws.

  30. INSTALL FRONT SEAT CUSHION ASSEMBLY LH


    1. A000X5IE02

      Install the front seat cushion assembly with the 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Attach the hook.

      Text in Illustration
      *1 Hook
    3. A000U62

      Attach the hook.

    4. A000UGS

      Install the 2 clips.

    5. A000VOH

      Connect the connector and attach the 2 wire harness clamps.

    6. A000W7X

      Connect the connector and attach the wire harness clamp.

    7. A000YYX

      Connect the connector and attach the wire harness clamp.

    8. Attach the 4 claws to connect duct of the seat climate control blower LH.

    9. A000X7O

      Connect the connector.

    10. A000WNL

      Connect the duct of the seat climate control blower LH with the 3 screws.

    11. A000ZAF

      Attach the 2 claws to install the No. 6 air duct.

  31. INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH


    1. A000TT0

      Install the No. 1 interior illumination light assembly LH with the screw.

    2. Attach the clamp.

  32. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A000XA9E03
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Connect the connector and attach the wire harness clamp.

    2. Attach the 2 hooks to install the front seatback board sub-assembly LH.

    3. Install the 2 screws.

  33. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    A000VMY

    1. Attach the claw to install the front seat inner cushion shield LH.

    2. Install the 3 screws.

  34. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here

  35. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)


    1. A000XB9

      Install the front seat inner No. 1 cushion shield LH with the 3 screws.

  36. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A000VVTE01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Install the front seat inner No. 1 cushion shield RH with the 3 screws.

  37. INSTALL FRONT POWER SEAT SWITCH LH

    A000TSZ

    1. Install the front power seat switch LH with the 4 screws.

  38. INSTALL FRONT NO. 1 SEAT SHIELD SET BRACKET

    A000VFW

    1. Install the front No. 1 seat shield set bracket with the 2 screws.

  39. INSTALL FRONT SEAT CUSHION SHIELD LH

    A000ZIKE02

    1. Connect the 2 connectors.

    2. Attach the 2 claws to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    3. Install the 3 screws.

    4. A000TSS

      Attach the rubber band of the front seatback board sub-assembly LH to the front seat adjuster assembly LH.