CURTAIN SHIELD AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  3. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  4. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  5. REMOVE BATTERY SERVICE HOLE COVER LH

    Click here

  6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE ROOF HEADLINING ASSEMBLY


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  8. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Standard Body)

    CAUTION:

    When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A000VCKE02
      Text in Illustration
      *1 Clip
      *2 Pin

      Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and raise the pin from the clip.

      Tech Tips

      Use the same procedure for the other clips as well.

    4. A000ZEFE02
      Text in Illustration
      *1 Clip
      *2 Curtain Shield Airbag Assembly LH
      *3 Body

      Using 2 screwdrivers, detach the 2 clips by inserting the screwdrivers into the grooves of the clips as shown in the illustration, and then remove the clips from the vehicle body.

      Tech Tips


      • The clip will remain installed to the curtain shield airbag assembly LH.

      • Use the same procedure for the other clips as well.

    5. A000TQWE01
      Text in Illustration
      *1 Clip
      *2 Curtain Shield Airbag Assembly LH

      Detach the 2 claws and remove the clip from the curtain shield airbag assembly LH.

      Note

      The clips must not be reused.

      Tech Tips

      Use the same procedure for the other clips as well.

    6. A000ZFM

      Using a screwdriver release the connector lock.

    7. Using a screwdriver, disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    8. Remove the 6 bolts in the order shown in the illustration to remove the curtain shield airbag assembly LH.

      A000UOOE03

      Note

      The bolts must not be reused.

  9. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH (for Long Body)

    CAUTION:

    When storing the curtain shield airbag assembly LH, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A000VCKE02
      Text in Illustration
      *1 Clip
      *2 Pin

      Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and raise the pin from the clip.

      Tech Tips

      Use the same procedure for the other clips as well.

    4. A000ZEFE02
      Text in Illustration
      *1 Clip
      *2 Curtain Shield Airbag Assembly LH
      *3 Body

      Using 2 screwdrivers, detach the 2 clips by inserting the screwdrivers into the grooves of the clips as shown in the illustration, and then remove the clips from the vehicle body.

      Tech Tips


      • The clip will remain installed to the curtain shield airbag assembly LH.

      • Use the same procedure for the other clips as well.

    5. A000TQWE01
      Text in Illustration
      *1 Clip
      *2 Curtain Shield Airbag Assembly LH

      Detach the 2 claws and remove the clip from the curtain shield airbag assembly LH.

      Note

      The clips must not be reused.

      Tech Tips

      Use the same procedure for the other clips as well.

    6. A000ZFM

      Using a screwdriver release the connector lock.

    7. Using a screwdriver, disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    8. Remove the 6 bolts in the order shown in the illustration to remove the curtain shield airbag assembly LH.

      A000UI5E03

      Note

      The bolts must not be reused.