SPIRAL CABLE INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL STEERING SENSOR


    1. A000YSAE02
      Text in Illustration
      *1 Pin

      Align the 2 pins of the spiral cable sub-assembly with the locations shown in the illustration and attach the 6 claws to install the spiral cable sub-assembly to the steering sensor.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY WITH SENSOR

    Note


    • Do not replace the spiral cable sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Attach the 3 claws to install the spiral cable sub-assembly with sensor.

      Note

      When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. A000TI2

      Connect the yellow airbag connector to the spiral cable sub-assembly with sensor.

    6. Connect the connectors to the spiral cable sub-assembly with sensor.

      Note

      When connecting airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL STEERING COLUMN COVER


    1. w/o Driver Monitor Camera:

      Click here

    2. w/ Driver Monitor Camera:

      Click here

  4. PLACE FRONT WHEELS TO FACING STRAIGHT AHEAD

  5. ADJUST SPIRAL CABLE SUB-ASSEMBLY WITH SENSOR

    Note

    Do not adjust the spiral cable sub-assembly with sensor with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check the check window shown in the illustration.

      Tech Tips

      When the spiral cable sub-assembly with sensor is centered, the connector is at the top and the conditions below can be checked.


      • w/o Steering Heater:

        With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

      • w/ Steering Heater:

        With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

      A000Z4PE08
      Text in Illustration
      *A w/o Steering Heater *B w/ Steering Heater
      *C for Type A *D for Type B
      *a Check Window *b Matchmark
      A000ZKM Colored Roller A000UMK U-turn Point

    4. If the spiral cable sub-assembly with sensor is not centered, center it.

    5. A000Y09

      Rotate the spiral cable sub-assembly with sensor counterclockwise slowly by hand until it stops.

      CAUTION:

      Do not turn the spiral cable sub-assembly with sensor using the airbag wire harness.

    6. Rotate the spiral cable sub-assembly with sensor 2.5 times clockwise from the lock position to align the matchmarks and check the check window.

      Tech Tips


      • The spiral cable sub-assembly with sensor will rotate approximately 2.5 turns to both the left and right from the center.

      • When the spiral cable sub-assembly with sensor is centered, the connector is at the top and the conditions below can be checked.


      • w/o Steering Heater:

        With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

      • w/ Steering Heater:

        With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.

      A000XO9E08
      Text in Illustration
      *A w/o Steering Heater *B w/ Steering Heater
      *C for Type A *D for Type B
      *a Check Window *b Matchmark
      A000ZKM Colored Roller A000UMK U-turn Point

      If the spiral cable sub-assembly with sensor cannot be centered, it is possible that the spiral cable sub-assembly with sensor is broken. Replace the spiral cable sub-assembly with sensor with a new one.

  6. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  7. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note


    • Make sure that the cable has been disconnected from the auxiliary battery terminal for at least 2 seconds before reconnecting the cable.

    • Connect the cable to the negative (-) auxiliary battery terminal with the front wheels facing straight ahead.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.

  9. INSPECT STEERING PAD


    1. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  12. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  13. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  14. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here