AIRBAG SYSTEM, Diagnostic DTC:B1920/77, B1921/77, B1922/77, B1923/77

DTC Code DTC Name
B1920/77 Short in Rear Pretensioner Squib RH Circuit
B1921/77 Open in Rear Pretensioner Squib RH Circuit
B1922/77 Short to GND in Rear Pretensioner Squib RH Circuit
B1923/77 Short to B+ in Rear Pretensioner Squib RH Circuit

DESCRIPTION

The rear pretensioner squib RH circuit consists of the center airbag sensor assembly and the rear seat outer belt RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

Theses DTCs are recorded when a malfunction is detected in the rear pretensioner squib RH circuit.

DTC Code Detection Condition Trouble Area
B1920/77

One of the following conditions is met:


  • The center airbag sensor assembly receives a line short circuit signal 5 times in the rear pretensioner squib RH circuit during the primary check.

  • Rear pretensioner squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat outer belt assembly RH (Rear pretensioner squib RH)

  • Center airbag sensor assembly
B1921/77

One of the following conditions is met:


  • The center airbag sensor assembly receives an open circuit signal in the rear pretensioner squib RH circuit for 2 seconds.

  • Rear pretensioner squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat outer belt assembly RH (Rear pretensioner squib RH)

  • Center airbag sensor assembly
B1922/77

One of the following conditions is met:


  • The center airbag sensor assembly receives a short circuit to ground signal in the rear pretensioner squib RH circuit for 0.5 seconds.

  • Rear pretensioner squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat outer belt assembly RH (Rear pretensioner squib RH)

  • Center airbag sensor assembly
B1923/77

One of the following conditions is met:


  • The center airbag sensor assembly receives a short circuit to B+ signal in the rear pretensioner squib RH circuit for 0.5 seconds.

  • Rear pretensioner squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat outer belt assembly RH (Rear pretensioner squib RH)

  • Center airbag sensor assembly

WIRING DIAGRAM

A000Y2VE11
*a Rear Pretensioner Squib RH
*b Center Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the power switch OFF, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

Tech Tips


  • Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester Click here.

  • After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads Click here.

PROCEDURE


  1. CHECK REAR SEAT OUTER BELT RH

    A000XUAE02
    *1 Center Airbag Sensor Assembly
    *2 Rear Pretensioner Squib RH
    *3 Front view of wire harness connector: (to Rear Pretensioner Squib RH)
    *4 Connector C

    1. Turn the power switch OFF.

    2. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    3. Disconnect the connectors from the rear seat outer belt RH.

    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the rear seat outer belt RH (rear pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 2 seconds.

    6. Turn the power switch ON (IG), and wait for at least 60 seconds.

    7. Clear the DTCs stored in the memory Click here.

    8. Turn the power switch OFF.

    9. Turn the power switch ON (IG), and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1920, B1921, B1922 or B1923 is not output.

      Tech Tips

      Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.


    OK

    REPLACE REAR SEAT OUTER BELT ASSEMBLY RH Click here

    NG

  2. CHECK CONNECTORS


    1. Turn the power switch OFF.

    2. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    3. Disconnect SST from connector C.

    4. Check that the floor wire connector (on the rear seat outer belt RH side) is not damaged.

      OK
      The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE (REAR PRETENSIONER SQUIB RH CIRCUIT)

    A000XM4E02

    1. Disconnect the connectors from the center airbag sensor assembly.

    2. Connect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    3. Turn the power switch ON (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      R93-1 (RR+) - Body ground Power switch ON (IG) Below 1 V
      R93-2 (RR-) - Body ground Power switch ON (IG) Below 1 V

    5. Turn the power switch OFF.

    6. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    7. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      R93-1 (RR+) - R93-2 (RR-) Always Below 1 Ω

    8. Release the activation prevention mechanism built into connector B Click here.

    9. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      R93-1 (RR+) - R93-2 (RR-) Always 1 MΩ or higher
      R93-1 (RR+) - Body ground Always 1 MΩ or higher
      R93-2 (RR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

    A000WGIE92
    *1 Center Airbag Sensor Assembly
    *2 Rear Pretensioner Squib RH

    1. Connect the connectors to the rear seat outer belt RH and the center airbag sensor assembly.

    2. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 90 seconds.

    3. Turn the power switch ON (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory Click here.

    5. Turn the power switch OFF.

    6. Turn the power switch ON (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1920, B1921, B1922 or B1923 is not output.

      Tech Tips

      Codes other than DTC B1920, B1921, B1922 and B1923 may be output at this time, but they are not related to this check.


    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here