NIGHT VIEW SYSTEM Night View Image is not Normal

DESCRIPTION

The No. 1 night view ECU receives the front image signal from the object recognition camera (night view camera). Using the digital (GVIF cable) signal line, the image data is sent to the accessory meter assembly.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK FOR DIRT AND DAMAGE

   
   

   1. Check that the area of the front windshield glass in front of the object recognition camera (night view camera), object recognition camera (night view camera) lens and/or headlights lens is free of dirt and damage.

      OK
      There is no dirt or damage.

   
   

   NG

   CLEAN OR REPLACE DAMAGED PARTS

   OK

2. CHECK HARNESS AND CONNECTOR (NO. 1 NIGHT VIEW ECU - OBJECT RECOGNITION CAMERA [NIGHT VIEW CAMERA])

   
   

   1. Disconnect the p2 No. 1 night view ECU connector.

   2. Disconnect the X17 object recognition camera (night view camera) connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition p2-17 (CCD+) - X17-1 (CB+) Always Below 1 Ω p2-18 (NTSC) - X17-4 (CV+) Always Below 1 Ω p2-19 (CLTS) - X17-3 (CC+) Always Below 1 Ω p2-20 (CCD-) - X17-2 (CGND) Always Below 1 Ω p2-21 (SG) - X17-5 (SG2) Always Below 1 Ω p2-17 (CCD+) - Body ground Always 10 kΩ or higher p2-18 (NTSC) - Body ground Always 10 kΩ or higher p2-19 (CLTS) - Body ground Always 10 kΩ or higher p2-20 (CCD-) - Body ground Always 10 kΩ or higher p2-21 (SG) - Body ground Always 10 kΩ or higher p2-17 (CCD+) - p2-18 (NTSC) Always 10 kΩ or higher p2-17 (CCD+) - p2-19 (CLTS) Always 10 kΩ or higher p2-17 (CCD+) - p2-20 (CCD-) Always 10 kΩ or higher p2-17 (CCD+) - p2-21 (SG) Always 10 kΩ or higher p2-18 (NTSC) - p2-19 (CLTS) Always 10 kΩ or higher p2-18 (NTSC) - p2-20 (CCD-) Always 10 kΩ or higher p2-18 (NTSC) - p2-21 (SG) Always 10 kΩ or higher p2-19 (CLTS) - p2-20 (CCD-) Always 10 kΩ or higher p2-19 (CLTS) - p2-21 (SG) Always 10 kΩ or higher p2-20 (CCD-) - p2-21 (SG) Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

3. CHECK OBJECT RECOGNITION CAMERA (NIGHT VIEW CAMERA)

   
   
   1. 

      Text in Illustration

      *a	Component with harness connected (Object Recognition Camera [Night View Camera])

      Measure the pulse from the rear of the object recognition camera (night view camera).

      Measurement Condition

      Item	Content
      Terminal No. (Symbol)	X17-4 (CV+) - X17-2 (CGND)
      Tool Setting	200 mV/DIV., 10 μs./DIV.
      Condition	Night view system operating and image output to accessory meter assembly

      OK
      The pulse changes according to the image from object recognition camera (night view camera).

   
   

   NG

   REPLACE OBJECT RECOGNITION CAMERA (NIGHT VIEW CAMERA) Click here

   OK

4. REPLACE HARNESS AND CONNECTOR (GVIF CABLE)

   
   

   1. Temporarily replace the wire harness and connector (GVIF cable) with a new or normally functioning one.

   
   

   NEXT

5. CHECK SYMPTOMS

   
   

   1. Confirm that the "night view image is not normal" problem symptom is not present.

      OK
      Symptom is not present.

   
   

   OK

   END (GVIF CABLE IS DEFECTIVE)

   NG

6. REPLACE NO. 1 NIGHT VIEW ECU

   
   

   1. Temporarily replace the No. 1 night view ECU with a new or normally functioning one Click here.

   
   

   NEXT

7. ADJUST OBJECT RECOGNITION CAMERA (NIGHT VIEW CAMERA)

   
   

   1. Perform object recognition camera (night view camera) adjustment Click here.

   
   

   NEXT

8. CHECK SYMPTOMS

   
   

   1. Confirm that the "night view image is not normal" problem symptom is not present.

      OK
      Symptom is not present.

   
   

   OK

   END (NO. 1 NIGHT VIEW ECU IS DEFECTIVE)

   NG

   REPLACE ACCESSORY METER ASSEMBLY Click here