AUDIO AND VISUAL SYSTEM, Diagnostic DTC:B157D

DTC Code DTC Name
B157D DAB Tuner Antenna Disconnected

DESCRIPTION

This DTC is stored when a malfunction occurs in the No. 2 amplifier antenna assembly which is connected to the multi-media module receiver assembly.

DTC Code DTC Detection Condition Trouble Area
B157D The No. 2 amplifier antenna assembly is not connected

  • Antenna cord sub-assembly

  • No. 2 antenna cord sub-assembly

  • No. 3 antenna cord sub-assembly

  • No. 2 amplifier antenna assembly

  • Multi-media module receiver assembly

WIRING DIAGRAM

A000YJTE11

CAUTION / NOTICE / HINT

Note


  • Check that the antenna cable is properly installed and does not have any sharp bends, pinching or loose connections.

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

    Click here

PROCEDURE


  1. CHECK CONNECTION OF DAB RADIO ANTENNA CABLE


    1. Check if the DAB radio antenna cable is securely connected to the multi-media module receiver assembly.

      OK
      DAB radio antenna cable is securely connected.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY CONNECT DAB RADIO ANTENNA CABLE

    OK

  2. CHECK VEHICLE TYPE


    1. Check the vehicle type.

      Model
      Model Proceed to
      w/o Telematics Transceiver A
      w/ Telematics Transceiver B

    B

    CHECK ANTENNA CORD SUB-ASSEMBLY Click here

    A

  3. CHECK ANTENNA CORD SUB-ASSEMBLY


    1. A000YLMC02
      *a

      Front view of wire harness connector

      (to Multi-media Module Receiver Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Remove the antenna connector from the multi-media module receiver assembly.

    2. Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      DB-1 (DAB) - 1 Always Below 1 Ω
      DB-1a - 1a Always Below 1 Ω
      DB-1 (DAB) or 1 - Body ground Always 10 kΩ or higher
      DB-1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  4. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A000ZW2C01
      *a

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)

      Remove the antenna connector from the antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 3 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 1 Always Below 1 Ω
      1a - 1a Always Below 1 Ω
      1 or 1 - Body ground Always 10 kΩ or higher
      1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  5. CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. A000XZJC02
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Amplifier Antenna Assembly)

      Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 2 amplifier antenna assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 1 Always Below 1 Ω
      1a - 1a Always Below 1 Ω
      1 or 1 - Body ground Always 10 kΩ or higher
      1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  6. REPLACE NO. 2 AMPLIFIER ANTENNA ASSEMBLY


    1. Replace the No. 2 amplifier antenna assembly with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. CLEAR DTC


    1. Clear the DTCs.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. CHECK FOR DTC


    1. Recheck for DTCs and check if the same DTC is output again.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (NO. 2 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  9. CHECK ANTENNA CORD SUB-ASSEMBLY


    1. A000YLMC02
      *a

      Front view of wire harness connector

      (to Multi-media Module Receiver Assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)

      Remove the antenna connector from the multi-media module receiver assembly.

    2. Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      DB-1 (DAB) - 1 Always Below 1 Ω
      DB-1a - 1a Always Below 1 Ω
      DB-1 (DAB) or 1 - Body ground Always 10 kΩ or higher
      DB-1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  10. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. A000TXFC01
      *a

      Front view of wire harness connector

      (to Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 3 Antenna Cord Sub-assembly)

      Remove the antenna connector from the antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 3 antenna cord sub-assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 1 Always Below 1 Ω
      1a - 1a Always Below 1 Ω
      1 or 1 - Body ground Always 10 kΩ or higher
      1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  11. CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY


    1. A000XCFC01
      *a

      Front view of wire harness connector

      (to No. 2 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to No. 2 Amplifier Antenna Assembly)

      Remove the antenna connector from the No. 2 antenna cord sub-assembly.

    2. Remove the antenna connector from the No. 2 amplifier antenna assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 1 Always Below 1 Ω
      1a - 1a Always Below 1 Ω
      1 or 1 - Body ground Always 10 kΩ or higher
      1a or 1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 6 Click here

    NG

    REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY Click here