STEERING COLUMN ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RHD and LHD.

  • The procedures listed below are for the LHD.

PROCEDURE


  1. INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. Install the steering column assembly with the 4 nuts.

      Torque:
      26 N*m  { 260 kgf*cm, 19 ft.*lbf }

    2. Connect the connectors and wire harness clamps to the steering column.

  2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. Install the clamp to the steering column hole cover sub-assembly.

    2. A000YCGE04
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column.

    3. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    4. A000Z50E03
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the No. 2 steering intermediate shaft assembly and power steering link.

    5. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

  3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    1. Attach the 2 claws to install the air duct.

    2. Install the bolt.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    3. Attach the 2 claws and install the wiring harness protector.

  5. INSTALL NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY LOWER

    Click here

  6. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Install the turn signal switch assembly with spiral cable to the steering column with the clamp.

    2. Connect the connectors to the turn signal switch assembly with spiral cable.

  7. INSTALL STEERING COLUMN COVER (w/o Driver Monitor Camera)


    1. Attach the claw to install the upper steering column cover.

    2. Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

    3. Attach the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    4. Install the 3 screws.

  8. INSTALL STEERING COLUMN COVER (w/ Driver Monitor Camera)


    1. Connect the driver monitor connector.

    2. Attach the claw to install the upper steering column cover.

    3. Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

    4. Attach the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    5. Install the 3 screws.

  9. ADJUST SPIRAL CABLE SUB-ASSEMBLY

    Click here

  10. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  11. INSPECT STEERING WHEEL CENTER POINT

  12. INSPECT STEERING PAD

    Click here.

  13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note


    • Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  15. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  16. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  17. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  18. CHECK SRS WARNING LIGHT

    Click here.