POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM, Diagnostic DTC:B2611

DTC Code DTC Name
B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction

DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (hall IC) in the telescopic motor detects the sliding position in the forward and backward directions of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

A000V85E21

Tech Tips

Limit positions can be confirmed on the screen of the intelligent tester.

DTC Code Detection Item Trouble Area
B2611 Telescopic operation stops within the operation range while operating.

  • Harness or connector

  • Telescopic position sensor or telescopic motor

  • Multiplex tilt and telescopic ECU

WIRING DIAGRAM

A000W5RE19

CAUTION / NOTICE / HINT

Tech Tips

The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the steering column assembly.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCOPIC SHORT/LONG)

    A000Z9XE09
    *1 Extend
    *2 Contract

    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the telescopic operation.

      Tilt & Telescopic:
      Tester Display Test Part Control Range Diagnostic Note
      Telesco Operation Telescopic operation Long / Short -
      Result
      Result Proceed to
      The steering column does not contract/extend. A
      The steering column contracts/extends. B

    B

    CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE) Click here

    A

  2. CHECK TELESCOPIC MOTOR


    1. A000W4GE23
      *1 Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU)
      *2 Connector A

      Disconnect connector A from the multiplex tilt and telescopic ECU.

    2. Apply the 12 V battery voltage to the multiplex tilt and telescopic ECU connector. Then check the steering wheel telescopic operation.

      OK
      Measurement Condition Specified Condition

      12 V battery positive (+) → Terminal A-2 (TEM+)

      12 V battery negative (-) → Terminal A-6 (TEM-)

      		 The steering column contracts.

      12 V battery positive (+) → Terminal A-6 (TEM-)

      12 V battery negative (-) → Terminal A-2 (TEM+)

      		 The steering column extends.

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

    NG

    REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) Click here

  3. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE TERMINAL VOLTAGE)


    1. A000UV6E43
      *1 Component with harness connected: (Multiplex Tilt and Telescopic ECU)
      *2 Connector A

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      A-3 (VCE) - A-5 (E2) Power switch ON (IG) 8 to 16 V

    NG

    CHECK HARNESS AND CONNECTOR (ECU - TELESCOPIC POSITION SENSOR) Click here

    OK

  4. CHECK TELESCOPIC POSITION SENSOR


    1. A000UV6E44
      *1 Component with harness connected: (Multiplex Tilt and Telescopic ECU)
      *2 Connector A

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      A-4 (TES) - A-5 (E2) Telescopic steering contracted or extended

      Pulse generation

      HI: 8 to 16 V

      LOW: 0 V

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

    NG

    REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) Click here

  5. CHECK HARNESS AND CONNECTOR (ECU - TELESCOPIC POSITION SENSOR)


    1. A000W4GE24
      *1 Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU)
      *2 Connector A

      Disconnect connector A from the multiplex tilt and telescopic ECU.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A-3 (VCE) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (ECU - BODY GROUND)


    1. A000XIJE06
      *1 Rear view of wire harness connector: (to Multiplex Tilt and Telescopic ECU)

      Disconnect the L34 multiplex tilt and telescopic ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      L34-11 (GND) - Body ground Always Below 1 Ω

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR