BRAKE ACTUATOR(for RHD) REMOVAL

CAUTION / NOTICE / HINT

Note

While the battery is connected, even if the power switch is OFF, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.

PROCEDURE


  1. REMOVE V-BANK COVER SUB-ASSEMBLY

    Click here

  2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  3. DISCONNECT BRAKE ACCUMULATOR PUMP CONNECTOR

    Click here

  4. PERFORM ACCUMULATOR ZERO DOWN

    Click here

  5. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

  6. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  7. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  8. REMOVE BATTERY SERVICE HOLE COVER LH

    Click here

  9. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary batter terminal notice before proceeding with work Click here.

  10. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. DISCONNECT NO. 2 INVERTER COOLING PIPE

    Click here

  12. REMOVE SKID CONTROL ECU

    Click here

  13. REMOVE SKID CONTROL ECU BRACKET

    Click here

  14. DISCONNECT NO. 3 RELAY BLOCK


    1. A000UYE

      While pushing the claw of the No. 3 relay block, pull out the No. 3 relay block and disconnect it from the reservoir bracket.

      Note

      Do not allow brake fluid to contact the No. 3 relay block.

  15. REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

    Click here

  16. REMOVE NO. 1 RESERVOIR HOSE

    Click here

  17. REMOVE RESERVOIR BRACKET

    Click here

  18. REMOVE FRONT WHEEL

  19. DISCONNECT BRAKE TUBE


    1. A000Y42

      Release the lock lever and disconnect the brake actuator connector.

      Note

      Do not allow brake fluid to contact the connector face.

    2. A000UTY

      Using a union nut wrench, disconnect the 6 brake tubes from the actuator.

    3. A000WYZE01

      Use tags or make a note to identify the reconnection locations.


      • *1: To FR RH

      • *2: To FR LH

      • *3: To: RR RH

      • *4: To RR LH

      • *5: From Brake Master Cylinder

      • *6: From Brake Stroke Simulator Cylinder

    4. A000U6Z

      Using a union nut wrench, disconnect the No. 1 and No. 2 brake actuator tubes.

      Note

      Do not damage the No. 1 and No. 2 brake actuator tubes.

  20. REMOVE BRAKE ACTUATOR AND BRAKE ACCUMULATOR PUMP ASSEMBLY


    1. A000WJU

      Disconnect the No. 1 brake actuator hose from the clamp and then remove the clamp.

    2. A000X3L

      Disconnect the front fender liner rear side and then remove the 2 nuts.

    3. Remove the bolt, and brake actuator and brake accumulator pump.

      Note


      • Do not damage the brake tubes.

      • When removing the brake actuator and brake accumulator pump from the vehicle, do not hold the connector, harness, hose or tube parts.

      • Do not drop the brake actuator and brake accumulator pump. Do not use parts that have been dropped.

  21. REMOVE NO. 5 BRAKE ACTUATOR BRACKET


    1. A000VNC

      Remove the bolt and No. 5 brake actuator bracket.

  22. REMOVE NO. 1 BRAKE ACTUATOR HOSE

    Note

    When disconnecting the hose, be careful that there is no excessive weight applied to the union of the brake actuator (especially in the union rotation direction).


    1. A000WZ3

      Remove the hose clip and No. 1 brake actuator hose.

  23. REMOVE BRAKE ACTUATOR PROTECTOR


    1. A000ZZJ

      Remove the protector.

  24. REMOVE NO. 2 BRAKE ACTUATOR HOSE

    Note

    When disconnecting the hose, be careful that there is no excessive weight applied to the union of the brake accumulator pump (especially in the union rotation direction).


    1. A000WI0

      Remove the hose clip and No. 2 brake actuator hose.

    2. A000WKC

      Remove the hose clip and reservoir connector.

  25. REMOVE NO. 3 BRAKE ACTUATOR TUBE

    Note


    • Do not damage the No. 3 brake actuator tube, brake actuator and brake accumulator pump.

    • When removing the No. 3 brake actuator tube, hold the tube, brake actuator and brake accumulator pump securely.


    1. A000T9E

      Using a union nut wrench, disconnect the No. 3 brake actuator tube.

  26. DISCONNECT BRAKE ACCUMULATOR PUMP CONNECTOR BOX


    1. A000YP0E06
      Text in Illustration
      *1 Connector Box

      Disconnect the brake accumulator pump connector box.


      1. Detach the 2 wiring harness clamps.

      2. Remove the nut and connector box.

  27. REMOVE NO. 4 BRAKE ACTUATOR BRACKET


    1. A000UW0

      Remove the bolt and No. 4 brake actuator bracket.

  28. REMOVE BRAKE ACCUMULATOR PUMP


    1. A000TZQE01
      Text in Illustration
      *1 Brake Accumulator Pump
      *2 Clamp (A)
      *3 Bush (B)

      Break and remove the brake actuator bracket clamp (labeled A), and then remove the brake accumulator pump.

    2. Remove the brake booster pump bush (labeled B) from the brake actuator bracket.

    3. Remove the brake booster pump bushes (labeled C) and brake booster pump collars (labeled D) from the brake accumulator pump.

  29. REMOVE BRAKE ACTUATOR


    1. A000YV2

      Remove the 3 bolts, brake actuator bracket and brake actuator.

    2. A000X2BE01
      Text in Illustration
      *1 Cushion
      *2 Spacer

      Remove the 3 cushions and 3 spacers from the brake actuator bracket.

    3. A000WML

      Remove the 3 bolts and No. 3 brake actuator bracket from the brake actuator.