FRONT UPPER SUSPENSION ARM INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. TEMPORARILY INSTALL FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A000WQH

      Insert the bolt as shown in the illustration. Then temporarily install the front No. 1 suspension upper arm assembly LH to the inner No. 1 arm attachment plate LH with the nut.

  2. TEMPORARILY INSTALL FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A000V3T

      Insert the bolt as shown in the illustration. Then temporarily install the front No. 2 suspension upper arm assembly LH to the inner No. 2 arm attachment plate LH with the nut.

  3. INSTALL INNER NO. 1 ARM ATTACHMENT PLATE LH


    1. A000WYAE01
      *1 Spacer

      Install the inner No. 1 arm attachment plate LH and spacers with the 3 bolts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  4. INSTALL INNER NO. 2 ARM ATTACHMENT PLATE LH


    1. A000Y81E02
      *1 Spacer

      Install the inner No. 2 arm attachment plate LH and spacer with the 2 bolts.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  5. INSTALL FRONT PNEUMATIC CYLINDER O-RING LH

    Click here

  6. INSTALL FRONT PNEUMATIC SHOCK ABSORBER WITH CYLINDER ASSEMBLY LH

    Click here

  7. INSTALL ABSORBER CONTROL ACTUATOR

    Click here

  8. INSTALL FRONT SHOCK ABSORBER CAP LH

    Click here

  9. INSTALL ENGINE ROOM SIDE COVER LH

    Click here

  10. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY

    Click here

  11. TEMPORARILY INSTALL LOWER FRONT SHOCK ABSORBER BRACKET SUB-ASSEMBLY LH

    Click here

  12. CONNECT NO. 4 HEIGHT CONTROL TUBE

    Click here

  13. REPAIR AIR CONNECTOR CLIP HOLDER

    Click here

  14. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  15. CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  16. INSTALL STEERING KNUCKLE SUB-ASSEMBLY LH

    Click here

  17. CONNECT FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH

    Click here

  18. CONNECT FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH

    Click here

  19. CONNECT TIE ROD ASSEMBLY LH

    Click here

  20. INSTALL FRONT SPEED SENSOR LH

    Click here

  21. CONNECT SKID CONTROL SENSOR WIRE

    Click here

  22. INSTALL FRONT DISC BRAKE DUST COVER LH

    Click here

  23. INSTALL FRONT DISC

    Click here

  24. CONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  25. INSTALL FRONT AXLE SHAFT NUT LH

    Click here

  26. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  27. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  28. STABILIZE SUSPENSION

    Click here

  29. TIGHTEN FRONT NO. 1 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A000UUD

      Tighten the installation nut of the front No. 1 suspension upper arm assembly LH.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  30. TIGHTEN FRONT NO. 2 SUSPENSION UPPER ARM ASSEMBLY LH


    1. A000WH4

      Tighten the installation nut of the front No. 2 suspension upper arm assembly LH.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  31. TIGHTEN LOWER FRONT SHOCK ABSORBER BRACKET SUB-ASSEMBLY LH

    Click here

  32. INSTALL FRONT WHEEL

    Click here

  33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT


    1. Inspect and adjust the front wheel alignment Click here.

  34. CHECK SUSPENSION CONTROL SYSTEM


    1. Check the suspension control system Click here.

  35. INSPECT FOR AIR LEAK


    1. Inspect for air leak Click here.

  36. ADJUST HEADLIGHT ASSEMBLY


    1. Adjust the headlight Click here.

  37. ADJUST OBJECT RECOGNITION CAMERA


    1. Adjust the object recognition camera Click here.