COOLANT(for Inverter) REPLACEMENT

PROCEDURE


  1. REMOVE ENGINE ROOM SIDE COVER RH

    Click here

  2. REMOVE ENGINE ROOM SIDE COVER LH

    Click here

  3. REMOVE FRONT CENTER FLOOR COVER

    Click here

  4. DRAIN COOLANT (for Inverter)

    Note


    • Do not reuse the drained coolant because it may contain foreign objects.

    • Collect the drained coolant and measure its volume to establish a benchmark. When adding coolant, make sure to add more coolant than the measured amount.


    1. Remove the inverter reserve tank cap.

      CAUTION:

      To avoid the danger of being burned, do not remove the inverter reserve tank cap while the coolant for the inverter is still hot.

      Note

      Do not remove the plug from the tube.

    2. A000Z4C

      Using a hexagon wrench 10 mm, remove the drain plug indicated in the illustration and drain the coolant.

      CAUTION:

      Use caution when handling coolant immediately after driving or in summer because it may be hot.

    3. Using a hexagon wrench 10 mm, install the drain plug with a new gasket.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

    4. Measure the volume of the drained coolant.

  5. ADD COOLANT (for Inverter)

    Note


    • Do not reuse the drained coolant because it may contain foreign objects.

    • If the vehicle is driven with air in the inverter cooling system, the following DTCs may be set.

      DTC Code Detection Item
      P0A01-725 Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
      P0A01-726 Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
      P0A78-284 Drive Motor "A" Inverter Performance
      P0A7A-322 Generator Inverter Performance
      P0A93-346 Inverter Cooling System Performance
      P0A94-553 DC / DC Converter Performance
      P0AEE-276 Motor Inverter Temperature Sensor "A" Circuit Range / Performance
      P0AEE-277 Motor Inverter Temperature Sensor "A" Circuit Range / Performance
      P3221-314 Generator Inverter Temperature Sensor Circuit Range / Performance
      P3221-315 Generator Inverter Temperature Sensor Circuit Range / Performance
      P3226-562 DC/DC Boost Converter Temperature Sensor
      P3226-563 DC/DC Boost Converter Temperature Sensor

    Tech Tips


    • for LHD:

      Coolant (for inverter) capacity: 2.6 liters (2.7 US qts, 2.3 Imp. qts.)

    • for RHD:

      Coolant (for inverter) capacity: 2.5 liters (2.5 US qts, 2.2 Imp. qts.)


    1. A000YD6

      for LHD:

      Remove the 2 clips and 2 plugs from the tubes.

      Note

      Do not reuse the clips or plugs.

    2. A000VAD

      for RHD:

      Remove the clip and plug from the tube.

      Note

      Do not reuse the clip or plug.

    3. Add coolant to the reserve tank.

    4. A000YD6

      for LHD:

      Install 2 new plugs and 2 new clips to the tubes.

    5. A000VAD

      for RHD:

      Install a new plug and new clip to the tube.

    6. Connect the intelligent tester to the DLC3.

    7. Select the following menu items: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

      Tech Tips

      The water pump can also be operated using inspection mode Click here.

    8. While adding coolant so that the coolant level is kept around the FULL line of the inverter reserve tank, operate the water pump for 3 minutes or more and then stop it for 1 minute or more.

    9. While adding coolant so that the coolant level is kept around the FULL line of the inverter reserve tank, operate the water pump for 1 minute or more and stop it for 1 minute or more. Repeat this procedure until bleeding is completed.

      Standard
      When the operation sound of the water pump becomes small or when no air bubbles can be seen in the inverter reserve tank, bleeding of the coolant system is complete.

      Tech Tips


      • If the water pump operates without a sufficient amount of coolant for approximately 5 seconds, the protective circuit will activate to stop the water pump for approximately 15 seconds. If a sufficient amount of coolant is added, the water pump will start operating automatically.

      • If an excessive amount of coolant is added to the inverter reserve tank, coolant may overflow when operation of the water pump is stopped.

    10. After bleeding is completed, add coolant to the FULL level, and install the inverter reserve tank cap.

      Note

      Make sure to add more coolant than was drained initially.

  6. INSPECT FOR COOLANT LEAK (for Inverter)

    Click here

  7. INSTALL FRONT CENTER FLOOR COVER

    Click here

  8. INSTALL ENGINE ROOM SIDE COVER LH

    Click here

  9. INSTALL ENGINE ROOM SIDE COVER RH

    Click here