DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Using the intelligent tester, enter the following menus: Powertrain / Cruise Control / Data List.
According to the display on intelligent tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed/min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) | Actual vehicle speed is display | - |
| CCS Mem Vehicle Spd | Vehicle speed/min.: 0 km/h (0 mph) max.: 255 km/h (159 mph) | Actual vehicle speed stored in memory | - |
| Cruise Operation Status | Shift lever position signal/ON or OFF | ON: Shift lever position D or S (8th, 7th, 6th, 5th or 4th) OFF: Shift lever except position D or S (8th, 7th, 6th, 5th or 4th) |
- |
| Cruise Control | Cruise control/ON or OFF | ON: Cruise control is SET OFF: Cruise control is UNSET |
- |
| CCS Indicator M-CPU | Cruise control indicator signal (M-CPU)/ON or OFF | ON: Cruise control indicator light is ON OFF: Cruise control indicator light is OFF |
- |
| CCS Ready M-CPU | Cruise control system standby condition (M-CPU)/ON or OFF | ON: Cruise control switch (M-CPU) is ON OFF: Cruise control switch (M-CPU) is OFF |
- |
| Main SW M-CPU | Cruise control switch (M-CPU)/ON or OFF | ON: Cruise control switch (M-CPU) is ON OFF: Cruise control switch (M-CPU) is OFF |
- |
| Vehicle Spd Change | Vehicle speed sudden change signal/ON or OFF | ON: Sudden vehicle speed change OFF: No sudden vehicle speed change |
- |
| Cancel Switch | CANCEL switch signal/ON or OFF | ON: CANCEL switch ON OFF: CANCEL switch OFF |
- |
| SET/COAST Switch | -/SET switch signal/ON or OFF | ON: -/SET switch ON OFF: -/SET switch OFF |
- |
| RES/ACC Switch | +/RES switch signal/ON or OFF | ON: +/RES switch ON OFF: +/RES switch OFF |
- |
| Stop Light SW M-CPU | Stop light switch signal (Main CPU)/ON or OFF | ON: Brake pedal is depressed OFF: Brake pedal is released |
- |
| Cruise Request Torque | Cruise control request torque/ min.: -1024 Nm, max.: 1016 Nm | Actual request torque | - |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other item to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Using the intelligent tester, enter following menus: Body / Combination Meter / Active test.
According to the display on intelligent tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Cruise | Cruise control indicator light | ON/OFF | - |
| Indicat. SET | SET indicator light | ON/OFF | - |