READ DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the power switch OFF.
Connect the intelligent tester to the DLC3.
Turn the power switch ON (IG).
Turn the tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on tester, read the "Data List".
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ACC SW | Power switch ON (ACC)/ON or OFF | ON: Power switch is ON (ACC) OFF: Power switch is OFF |
- |
| IG SW | Power switch ON (IG)/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| Stop Light SW | Stop light switch/ON or OFF | ON: Brake pedal is depressed OFF: Brake pedal is released |
- |
| Start Switch1 | Start switch 1/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| Start Switch2 | Start switch 2/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| Steering Unlock Switch | Steering lock condition/ON or OFF | ON: Steering is unlocked OFF: Steering is locked |
- |
| Shift P Signal | Shift P position signal/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
- |
| Vehicle Speed Signal | Vehicle speed signal/STOP or RUN | STOP: Vehicle is stopped RUN: Vehicle is running |
- |
| IG1 Relay Monitor(Outside) | D-IG1-1 relay outer relay monitor/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| IG2 Relay Monitor(Outside) | Ignition relay No. 2 (IG2) outer relay monitor/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| IG1 Relay Monitor(Inside) | D-IG1-1 relay inner relay monitor/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| IG2 Relay Monitor(Inside) | Ignition relay No. 2 (IG2) inner relay monitor/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| ACC Relay Monitor | D-ACC relay monitor/ON or OFF | ON: Power switch is ON (ACC) OFF: Power switch is OFF |
- |
| Latch Circuit | Latch circuit/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF, ON (ACC) |
- |
| Starter Request Signal | Hybrid control system start request signal/ON or OFF | ON: STSW signal is ON OFF: STSW signal is OFF |
- |
| Power Supply Condition | Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON | ALL OFF: All relays are OFF ACC ON: D-ACC relay is ON IG2 ON: Ignition relay No. 2 (IG2) is ON ST ON: STSW signal is ON |
- |
| Ready Signal | Hybrid control system start request signal monitor/ON or OFF | ON: System is ON (READY) OFF: System is OFF |
Power switch pressed and held with shift lever in P |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Ignition Switch | Power switch/ON or OFF | ON: Power switch is ON (IG) OFF: Power switch is OFF |
- |
| Unmatched Vehicle-ID | Key number/YES or NO | YES: Key number matches NO: Key number differs |
- |
| No Response | Response/YES or NO | YES: Response NO: No response |
- |
| Unmatch Code or Form | Code format/YES or NO | YES: Code format matches NO: Code format differs |
- |
| Key Low Battery | Key battery conditions/ON or OFF | ON: Battery is depleted OFF: Battery is not depleted |
- |
| #Codes | Number of diagnosis codes | - | - |
| ID Code Difference(Resp) | ID code/YES or NO | YES: ID code matches NO: ID code differs |
- |
| C Code Difference | Challenge code/YES or NO | YES: Challenge code matches NO: Challenge code differs |
- |
| S Code Check | S code certification result/NG or OK | OK: S code certification result is normal NG: S code certification result is abnormal |
- |
| L Code Check | L code certification result/NG or OK | OK: L code certification result is normal NG: L code certification result is abnormal |
- |
| Ignition Available Area | Key area where hybrid control system can be operated/ALL or FRONT | All: All areas Front: Front only |
- |
PERFORM ACTIVE TEST
Tech Tips
Using the intelligent tester to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the power switch OFF.
Connect the intelligent tester to the DLC3.
Turn the power switch ON (IG).
Turn the tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on tester, perform the "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicator for Lighting | Indicator illumination | ON/OFF | - |
| Indicator Condition | Indicator light illumination pattern | Green/Amber/No Sig | - |
| P Supply for Steering Lock | Steering lock ECU power supply | ON/OFF | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Fr-Seat Inside Transmitter | Indoor key antenna (for front) | ON / OFF | - |
| Rr-Seat Inside Transmitter | Indoor key antenna (for rear1) | ON / OFF | - |
| Inside Trunk/Backdoor Transmitter | Indoor key antenna (for rear2) | ON / OFF | - |
| Outside Trunk/Backdoor Transmitter | Electrical key antenna | ON / OFF | - |