SFI SYSTEM FAIL-SAFE CHART

If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC	Component	Fail-safe Operation	Fail-safe Deactivation Condition
P0010, P0020, P1023, P1360, P1361, P1362, P1363, P2614	Camshaft Timing Control Motor	Power to camshaft timing control motor is cut Valve timing of bank that is operating normally is fixed at maximum retard angle	Pass condition detected and then power switch turned off
P0011, P0021	VVT System for Intake Side	Idling up (misfire prevention), or power to camshaft timing control motor is cut Valve timing of bank that is operating normally is fixed at maximum retard angle	Pass condition detected and then power switch turned off
P0012, P0022	VVT System for Intake Side	Power to camshaft timing control motor is cut Valve timing of bank that is operating normally is fixed at maximum retard angle	Pass condition detected and then power switch turned off
P0016, P0018	Valve Timing Deviation	Power to camshaft timing control motor is cut Valve timing of bank that is operating normally is fixed at maximum retard angle	Pass condition detected and then power switch turned off
P0031, P0032, P0051, P0052	Air-Fuel Ratio (A/F) Sensor Heater	ECM turns off A/F sensor heater	Power switch off
P0037, P0038, P0057, P0058	Heated Oxygen (HO2) Sensor Heater	ECM turns off HO2 sensor heater	Power switch off
P0087, P0088	Fuel Pump (for High Pressure)	Stops the fuel pump (for High Pressure) Limits the engine speed to 2000 rpm or less	Pass condition detected
P0102, P0103, P010C, P010D	Mass Air Flow (MAF) Meter	ECM calculates ignition timing according to engine speed and throttle valve position	Pass condition detected
P00AC, P00AD, P0112, P0113	Intake Air Temperature (IAT) Sensor	ECM estimates IAT to be 20°C (68°F)	Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119, P2135	Electronic Throttle Control System (ETCS)	ECM cuts off throttle actuator current and throttle valve returns to 7° throttle position by return spring. The ECM stops the engine and the vehicle can be driven using solely the hybrid system*.	Pass condition detected and then power switch turned off
P0190, P0192, P0193	Fuel Pressure Sensor	Stops the fuel pump (for High Pressure) Limits the engine speed to 2000 rpm or less	Pass condition detected and then power switch turned off
P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P062D, P062E	Injector Driver (EDU)	Stops fuel injection (for Direct Injection) an abnormal cylinder and related other cylinders Limits the engine speed to 3000 rpm or less	Pass condition detected and then power switch turned off
P0327, P0328, P0332, P0333 P032C, P032D, P033C, P033D	Knock Sensor	ECM sets ignition timing to maximum retard	Power switch off
P0351 to P0358	Ignition Coil	ECM cuts fuel	Pass condition detected
P1235, P1236	Fuel Pump (for High Pressure) (Spill Control Valve)	Stops the fuel pump (for High Pressure) Limits the engine speed to 2000 rpm or less	Pass condition detected
P1276, P1277, P1278, P1279, P127A, P127B, P127C, P127D	Fuel Injector (for Port Injection)	Limits the engine speed to 2000 rpm or less Fuel cut of malfunction cylinder	Pass condition detected and then power switch turned off
P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256	A/F Sensor	Air-fuel ratio feedback control is stopped	Pass condition detected and then power switch turned off

Note

*: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.