ENTRY AND START SYSTEM Rear Door LH Entry Unlock Function does not Operate

DESCRIPTION

If the rear left door entry unlock function does not operate but the entry lock operation operates, the communication line between the vehicle and electrical key transmitter is normal. Either of the following may have occurred: 1) the door outside handle touch sensor is malfunctioning; or 2) the rear door ECU LH receives the door outside handle touch sensor ON signal, but is unable to send the signal to the certification ECU through CAN communication.

WIRING DIAGRAM

Refer to Rear Door LH Entry Lock and Unlock Functions do not Operate Click here.

CAUTION / NOTICE / HINT

Note

Before performing the inspection, check that there are no problems related to the "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the master switch's door control switch is operated, check that the locked doors unlock Click here.

      OK
      Locked doors unlock.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Using the intelligent tester, read the Data List Click here.

      Rear Left Door
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Lock Position SW Rear LH side door lock position switch signal / ON or OFF

      ON: Rear side door LH is unlocked

      OFF: Rear side door LH is locked

      		 -
      OK
      On intelligent tester screen, item changes between ON and OFF according to above chart.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Rear Door LH LOCK/UNLOCK Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (ENTRY SENSOR)


    1. Using the intelligent tester read the Data List Click here.

      Rear Left Door
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Entry Sensor Rear LH side door touch sensor / ON or OFF

      ON: Rear LH side door sensor is touched

      OFF: Rear LH side door sensor is not touched

      		 -
      OK
      On intelligent tester screen, item changes between ON and OFF according to above chart.

    NG

    CHECK HARNESS AND CONNECTOR (REAR DOOR LH - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

  4. CHECK REAR DOOR ECU LH (OPERATION)


    1. For Standard Body :


      1. Replace the rear door ECU LH with a new one or normally functioning one Click here.

    2. For Long Body :


      1. Replace the rear door ECU LH with a new one or normally functioning one Click here.

    3. Check that the entry function operates normally Click here.

      OK
      Operates normally

    OK

    END (REAR DOOR ECU LH IS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU

  5. CHECK HARNESS AND CONNECTOR (REAR DOOR LH - DOOR ELECTRICAL KEY OSCILLATOR)

    A000XF8E02
    *1 Front view of wire harness connector: (to Rear Door ECU LH)
    *2 Front view of wire harness connector: (to Door Electrical Key Oscillator)

    1. Disconnect the O14 ECU connector.

    2. Disconnect the O25 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      O14-16 (SEL) -O25-4 (SEL) Always Below 1 Ω
      O14-16 (SEL) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - REAR DOOR OUTSIDE HANDLE LH)

    A000Z0PE02
    *1 Front view of wire harness connector: (to Door Electrical Key Oscillator)
    *2 Front view of wire harness connector: (to Rear Door Outside Handle LH)

    1. Disconnect the O25 oscillator connector.

    2. Disconnect the O26 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      O25-2 (SGT8) -O26-6 (SGT7) Always Below 1 Ω
      O25-2 (SGT8) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. For Standard Body :


      1. Replace the door electrical key oscillator with a new one or normally functioning one Click here.

    2. For Long Body :


      1. Replace the door electrical key oscillator with a new one or normally functioning one Click here.

    3. Check that the entry function operates normally Click here.

      OK
      Operates normally

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

    NG

  8. CHECK REAR DOOR OUTSIDE HANDLE LH (OPERATION)


    1. For Standard Body :


      1. Replace the rear door outside handle LH with a new one or normally functioning one Click here.

    2. For Long Body :


      1. Replace the rear door outside handle LH with a new one or normally functioning one Click here.

    3. Check that the entry function operates normally Click here.

      OK
      Operates normally

    OK

    END (REAR DOOR OUTSIDE HANDLE LH IS DEFECTIVE)

    NG

  9. CHECK REAR DOOR ECU LH (OPERATION)


    1. For Standard Body :


      1. Replace the rear door ECU LH with a new one or normally functioning one Click here.

    2. For Long Body :


      1. Replace the rear door ECU LH with a new one or normally functioning one Click here.

    3. Check that the entry function operates normally Click here.

      OK
      Operates normally

    OK

    END (REAR DOOR ECU LH IS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU