FRONT WIPER MOTOR INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A000VP2

      Install the windshield wiper motor assembly with the 3 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  2. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY


    1. Check the automatic stop position.


      1. Check that the motor stops automatically at the automatic stop position Click here.

    2. A000W30

      Temporarily install the front wiper crank sub-assembly to the windshield wiper motor assembly with the nut.

    3. A000YI8

      Temporarily install the wiper link to the front wiper crank pivot.

    4. Align the front wiper crank sub-assembly with the wiper link as shown in the illustration.

      A000V7DE03
      *1 Windshield Wiper Link Pivot
      *2 Windshield Wiper Motor Shaft
      *3 Front Wiper Crank Pivot

    5. Tighten the front wiper crank sub-assembly nut.

      Torque:
      17 N*m  { 175 kgf*cm, 13 ft.*lbf }
    6. A000YAC

      Apply MP grease to the front wiper crank pivot of the front wiper crank sub-assembly.

    7. Install the wiper link to the front wiper crank pivot.

  3. INSTALL WIPER MOTOR COVER


    1. Attach the wiper motor cover.

  4. INSTALL WINDSHIELD WIPER LINK ASSEMBLY


    1. A000WDXE02

      Install the wiper motor and link assembly with the 4 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Connect the connector. Then attach the clamp to install the wire harness to the cowl top panel.

  5. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A000ZCH

      Push the ventilator louver in the direction indicated by the arrow in the illustration to attach the 9 claws and 2 clips and install the ventilator louver.

  6. INSTALL COWL TOP VENTILATOR LOUVER PROTECTOR RH


    1. A000UDM

      Attach the claw and guide to install the cowl top ventilator louver protector LH.

    2. Attach the clip.

  7. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


    1. A000WW5

      Attach the claw and clip to install the front fender to cowl side seal LH.

  8. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A000TEE

      Install the cowl top ventilator louver RH with the 6 clips.

      Note

      Be sure to install the cowl top ventilator louver RH properly. If it is not installed properly, water may enter the engine room and cause malfunctions.

  10. INSTALL HOOD TO COWL TOP SEAL


    1. A00103E

      Attach the 11 clips to install the cowl top seal.

  11. INSTALL FRONT UPPER FENDER PROTECTOR LH


    1. A000WBP

      Attach the clips to install the upper fender protector.

  12. INSTALL FRONT UPPER FENDER PROTECTOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL ENGINE ROOM SIDE COVER LH

    Click here

  14. INSTALL ENGINE ROOM SIDE COVER RH

    Click here

  15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSTALL FRONT WIPER ARM LH


    1. A000US7E04
      *1 Wiper Arm Serration
      *2 Wire Brush
      *3 Wiper Pivot Serration

      Stop the wiper motor at the automatic stop position.

    2. Clean the wiper arm serration with a round file or equivalent.

    3. Clean the wiper pivot serration with a wire brush.

    4. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

      A000UFNE01
      *1 for LHD:
      *2 for RHD:
      *3 Louver Edge
      Standard measurement
      Position Specified Condition
      A 16.3 mm (0.646 in.)
      B 61.7 to 76.7 mm (2.43 to 3.02 in.)
      C 23.2 mm (0.913 in.)
      D 35.6 to 50.6 mm (1.40 to 1.99 in.)
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold down the wiper arm hinge with your hand while tightening the nut.

  17. INSTALL FRONT WIPER ARM RH

    A000US7E04
    *1 Wiper Arm Serration
    *2 Wire Brush
    *3 Wiper Pivot Serration

    1. Stop the wiper motor at the automatic stop position.

    2. Clean the wiper arm serration with a round file or equivalent.

    3. Clean the wiper pivot serration with a wire brush.

    4. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

      A000UMCE03
      *1 for LHD:
      *2 for RHD:
      *3 Louver Edge
      Standard measurement
      Position Specified Condition
      A 23.2 mm (0.913 in.)
      B 35.6 to 50.6 mm (1.40 to 1.99 in.)
      C 16.3 mm (0.646 in.)
      D 61.7 to 76.7 mm (2.43 to 3.02 in.)
      Torque:
      22 N*m  { 224 kgf*cm, 16 ft.*lbf }

      Tech Tips

      Hold down the wiper arm hinge with your hand while tightening the nut.

    5. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.

  18. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  19. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

  20. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

  21. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here