LIGHTING SYSTEM Personal Light does not Illuminate

WIRING DIAGRAM

A000VNBE01

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CONFIRM LIGHT POSITION


    1. Check the malfunctioning personal light.

      Result
      Result Proceed to
      Rear personal light A
      Front personal light B

    B
    A
  2. CHECK HARNESS AND CONNECTOR (MAP LIGHT - BATTERY AND BODY GROUND)

    A000V5TE01
    *1 Front view of wire harness connector: (to Map Light)
    *2 DOME

    1. Disconnect the X4 map light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      X4-6 (+B) - Body ground Always 11 to 14 V
      X4-27 (DOME) - Body ground Always 11 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X4-16 (GND9) - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      OK (w/o Console Box) A
      OK (w/ Console Box) B
      NG C

    B
    C
    A
  3. INSPECT SPOT LIGHT ASSEMBLY


    1. Remove the spot light Click here.

    2. Inspect the spot light Click here.


    NG
    OK
  4. CHECK HARNESS AND CONNECTOR (MAP LIGHT - SPOT LIGHT)

    A000Z80E02

    1. Disconnect the X4 and X6 map light connector.

    2. Disconnect the X22 spot light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X4-3 (RLSW) - X22-6 (RLSW) Always Below 1 Ω
      X4-4 (RRSW) - X22-7 (RRSW) Always Below 1 Ω
      X6-7 (RLMP) - X22-4 (RLMP) Always Below 1 Ω
      X6-8 (RRMP) - X22-14 (RRMP) Always Below 1 Ω
      X4-15 (GND6) - X22-5 (RGND) Always Below 1 Ω
      X4-3 (RLSW) - Body ground Always 10 kΩ or higher
      X4-4 (RRSW) - Body ground Always 10 kΩ or higher
      X6-7 (RLMP) - Body ground Always 10 kΩ or higher
      X6-8 (RRMP) - Body ground Always 10 kΩ or higher
      X4-15 (GND6) - Body ground Always 10 kΩ or higher

    OK
    NG
  5. INSPECT CONSOLE BOX LIGHT ASSEMBLY


    1. Remove the console box light assembly Click here.

    2. Inspect the console box light assembly Click here.


    NG
    OK
  6. CHECK HARNESS AND CONNECTOR (MAP LIGHT - CONSOLE BOX LIGHT)

    A000XRPE02

    1. Disconnect the X4 and X6 map light connector.

    2. Disconnect the X22 spot light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      X4-3 (RLSW) - X22-6 (RLSW) Always Below 1 Ω
      X4-4 (RRSW) - X22-7 (RRSW) Always Below 1 Ω
      X6-7 (RLMP) - X22-4 (RLMP) Always Below 1 Ω
      X6-8 (RRMP) - X22-14 (RRMP) Always Below 1 Ω
      X4-15 (GND6) - X22-5 (RGND) Always Below 1 Ω
      X4-3 (RLSW) - Body ground Always 10 kΩ or higher
      X4-4 (RRSW) - Body ground Always 10 kΩ or higher
      X6-7 (RLMP) - Body ground Always 10 kΩ or higher
      X6-8 (RRMP) - Body ground Always 10 kΩ or higher
      X4-15 (GND6) - Body ground Always 10 kΩ or higher

    OK
    NG