THEFT DETERRENT SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus:


      1. Select: Body / (desired system) / Data List.

    5. According to the display on intelligent tester, read the "Data List".

      Body No. 5
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Hood Courtesy Switch

      Engine hood courtesy switch /

      ON or OFF

      ON: Engine hood is open

      OFF: Engine hood is closed

      		 -
      Security Horn Tr

      Security horn condition /

      OK / Heat / Load

      OK: Security horn is normal

      Heat: ECU is overheated

      Load: ECU internal short, wire short or security horn short

      		 -
      # Codes Number of diagnosis codes - -
      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Intrusion sensor OFF*1

      Intrusion sensor cancel switch /

      ON or OFF

      ON: Intrusion sensor active (switch OFF)

      OFF: Intrusion sensor not active (switch ON)

      		 -
      Intrusion sensor detection*1

      Intrusion sensor setting /

      ON or OFF

      ON: Intrusion sensor is set

      OFF: Intrusion sensor is not set

      		 -
      Tilt sensor detection*2

      Tilt sensor setting /

      ON or OFF

      ON: Tilt sensor is set

      OFF: Tilt sensor is not set

      		 -
      Intrusion sensor1 communication*1

      Intrusion sensor connecting /

      ON or OFF

      ON: Intrusion sensor connected

      OFF: Intrusion sensor not connected

      		 -
      Intrusion Sensor Sound Detect*3, *4

      Intrusion sensor sound detection /

      ON or OFF

      ON: Intrusion sensor detecting sound

      OFF: Intrusion sensor not detecting sound

      		 Only displays "ON" on the Data List once. When checking again, disconnect and reconnect the intelligent tester.
      Tilt sensor communication*2

      Tilt sensor connecting /

      ON or OFF

      ON: Tilt sensor connected

      OFF: Tilt sensor not connected

      		 -

      • *1: w/ Intrusion Sensor

      • *2: w/ Tilt Sensor

      • *3: w/ Emergency Call Switch

      Note

      *4: Perform the intrusion sensor operation inspection with the intelligent tester disconnected Click here.

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Test allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus:


      1. Select: Body / (desired system) / Active Test.

        Note

        When a Body No. 5 (front controller) related vehicle switch is on, Active Test items related to the vehicle switch are prohibited (double operation prohibition). Check that the vehicle switches are OFF before performing Active Tests.

    5. According to the display on intelligent tester, perform the "Active Test".

      Body No. 5
      Tester Display Test Part Control Range Diagnostic Note
      Security Horn Security horn ON / OFF -
      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Security Indicator Security indicator ON / OFF -
      Security Horn2*1 Theft warning siren ON / OFF -
      Power For Intrusion Sensor*2 Intrusion sensor power supply ON / OFF -
      Power For Tilt Sensor*3 Tilt sensor power supply ON / OFF -

      Tech Tips

      *1: w/ Theft Warning Siren (Self Power Siren)

      *2: w/ Intrusion Sensor

      *3: w/ Tilt Sensor