SEAT BELT WARNING SYSTEM Front Passenger Side Seat Belt Warning Light Malfunction

DESCRIPTION

The separate type front seat cushion pad (occupant detection sensor) detects if the front passenger seat is occupied and sends signals to the No. 1 meter ECU sub-assembly. The front seat inner belt assembly detects the front passenger seat belt condition and sends signals to the No. 1 meter ECU sub-assembly. After receiving the signals from the separate type front seat cushion pad (occupant detection sensor) and front passenger seat inner belt assembly, the seat belt warning light in the No. 1 meter ECU sub-assembly will blink or go off.

Tech Tips

The seat belt warning light on the No. 1 meter ECU sub-assembly is used for both the driver seat and front passenger seat.

WIRING DIAGRAM

A000XJXE08
A000XJXE09

CAUTION / NOTICE / HINT

Note

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure Click here.

PROCEDURE


  1. CHECK DTC OUTPUT (AIRBAG SYSTEM)


    1. Clear the DTCs Click here.

    2. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO AIRBAG SYSTEM Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (FRONT PASSENGER SIDE SEAT BELT)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Combination Meter (No. 1 meter ECU Sub-assembly)
      Tester Display Test Part Control Range Diagnostic Note
      Front Passenger Side Seat Belt Seat belt warning light OFF/ON -
      OK
      The front passenger side seat belt warning light on the No. 1 meter ECU sub-assembly operates normally.

    NG

    REPLACE NO. 1 METER ECU SUB-ASSEMBLY Click here

    OK

  3. READ VALUE USING GTS (PASSENGER DETECTION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / SRS Airbag / Data List.

    5. Read the Data List according to the display on the GTS.

      SRS Airbag (Center Airbag Sensor Assembly)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Passenger Detection Passenger Detection switch / None, Detect or NG

      Passenger Detection/

      None: No passenger

      Detect: A passenger is seated

      NG: Data is not determined

      		 -
      Result
      Result Proceed to
      None or Detect is displayed on the GTS screen according to the front passenger side seat belt condition A
      None or Detect is not displayed normally on the GTS screen according to the front passenger side seat belt condition B
      NG is displayed on the GTS screen C

    B

    INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR) Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    A

  4. READ VALUE USING GTS (LEFT SIDE BUCKLE SW, RIGHT SIDE BUCKLE SW)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / SRS Airbag / Data List.

    5. Read the Data List according to the display on the GTS.

      SRS Airbag (Center Airbag Sensor Assembly)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Left side Buckle SW*1 Left side seat belt buckle switch / Set, Unset or NG

      Set: Left side seat belt fastened

      Unset: Left side seat belt not fastened

      NG: Data is not determined

      		 -
      Right side Buckle SW*2 Right side seat belt buckle switch / Set, Unset or NG

      Set: Right side seat belt fastened

      Unset: Right side seat belt not fastened

      NG: Data is not determined

      		 -

      • *1: for RHD

      • *2: for LHD

      Result
      Result Proceed to
      Unset or Set is displayed on the GTS screen according to the front passenger side seat belt condition A
      Unset or Set is not displayed normally on the GTS screen according to the front passenger side seat belt condition B
      NG is displayed on the GTS screen C

    A

    REPLACE NO. 1 METER ECU SUB-ASSEMBLY Click here

    B

    REPLACE FRONT SEAT INNER BELT ASSEMBLY Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

  5. INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)


    1. A000USN

      Remove the separate type front seat cushion pad Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 1 Front passenger seat occupied Below 100 Ω
      2 - 1 Front passenger seat not occupied 1 MΩ or higher

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR) Click here