REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL REAR SEAT OUTER BELT ASSEMBLY CENTER

   

   *1

   Claw

   
   

   1. Align the seat belt positioning hole with the claw.

   2. Temporarily install the rear seat outer belt assembly center with the 2 bolts.

   3. Tighten the rear side bolt first, then the front side bolt to install the rear seat outer belt assembly center.

      Torque:

      for rear bolt

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      for front bolt

      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

   

   *1

   Claw

   
   

   1. Insert the claw of the retractor (a) into the hole.

   2. Align the seat belt positioning hole with the claw and install the retractor of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

   3. 

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

   4. w/ Tension Reducer System:

      Connect the tension reducer connector.

3. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

   

   *1

   Claw

   
   

   1. Insert the claw of the retractor (a) into the hole.

   2. Align the seat belt positioning hole with the claw and install the retractor of the rear seat 3 point type belt assembly RH with the bolt.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

   3. 

      Attach the wire harness clamp.

   4. Connect the pretensioner connector and lock the locking button as shown in the illustration.

   5. w/ Tension Reducer System:

      Connect the tension reducer connector.

4. INSTALL NO. 4 AIR DUCT REAR (w/ Rear Cooler)

   Click here

5. INSTALL NO. 5 AIR DUCT REAR (w/ Rear Cooler)

   Click here

6. INSTALL ROOF SIDE NO. 2 AIR DUCT LH (w/ Rear Cooler)

   Click here

7. INSTALL ROOF SIDE NO. 2 AIR DUCT RH (w/ Rear Cooler)

   Click here

8. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

   Click here

9. INSTALL INNER ROOF SIDE GARNISH LH

   Click here

10. INSTALL INNER ROOF SIDE GARNISH RH

    Click here

11. INSTALL REAR SEAT SIDE GARNISH LH

    Click here

12. INSTALL REAR SEAT SIDE GARNISH RH

    Click here

13. INSTALL REAR DOOR SCUFF PLATE LH

    
    

    1. for Standard Body:

       Click here

    2. for Long Body:

       Click here

14. INSTALL REAR DOOR SCUFF PLATE RH

    
    

    1. for Standard Body:

       Click here

    2. for Long Body:

       Click here

15. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

    
    

    1. for Power Seat:

       Click here

    2. for 5-Passenger with Ottoman:

       Click here

16. INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

    Click here

17. INSTALL REAR SEATBACK ASSEMBLY LH

    
    

    1. for Power Seat:

       Click here

    2. for Ottoman:

       Click here

18. INSTALL REAR SEATBACK ASSEMBLY RH

    
    

    1. for Power Seat:

       Click here

    2. for Ottoman:

       Click here

19. INSTALL REAR SEAT CONSOLE BOX ASSEMBLY (for 4-Passenger with Ottoman)

    Click here

20. INSTALL REAR SEAT LOWER CONSOLE BOX COVER (for 4-Passenger with Ottoman)

    Click here

21. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

    

    *1	Protruding Part

    
    

    1. Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

       Note

       Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding parts of the floor panel.

    2. Check if the ELR locks.

       Note

       The check should be performed with the rear seat 3 point type belt assembly LH installed.

       
       

       1. With the rear seat 3 point type belt assembly LH installed, check that the belt locks when it is pulled out quickly.

22. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

23. CONNECT REAR SEAT OUTER BELT ASSEMBLY CENTER

    

    *1	Protruding Part

    
    

    1. for Power Seat, 5-Passenger with Ottoman:

       Connect the anchor part of the rear seat outer belt assembly center with the nut.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

       Note

       Do not allow the anchor part of the rear seat outer belt assembly center to overlap the protruding parts of the floor panel.

    2. 

       *1	Protruding Part

       for Fixed Seat Type:

       Connect the anchor part of the rear seat outer belt assembly center with the nut.

       Torque:

       42 N*m  { 428 kgf*cm, 31 ft.*lbf }

       Note

       Do not allow the anchor part of the rear seat outer belt assembly center to overlap the protruding parts of the floor panel.

    3. Check if the ELR locks.

       Note

       The check should be performed with the outer belt assembly installed.

       
       

       1. With the rear seat outer belt assembly center installed, check that the belt locks when it is pulled out quickly.

24. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY

    
    

    1. for Power Seat:

       Click here

    2. for 5-Passenger with Ottoman:

       Click here

25. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

    Click here

26. INSTALL REAR SEAT CUSHION ASSEMBLY LH

    
    

    1. for Power Seat:

       Click here

    2. for Ottoman Seat:

       Click here

27. INSTALL REAR SEAT CUSHION ASSEMBLY RH

    
    

    1. for Power Seat:

       Click here

    2. for Ottoman Seat:

       Click here

28. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

29. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

30. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)

    Click here

31. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    Click here

32. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    Click here

33. CHECK SRS WARNING LIGHT

    Click here