LIGHTING SYSTEM(for LED Headlight) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus:


      1. Body Electrical / Main Body / Data List.

      2. Body Electrical / AFS / Data List.

      3. Body Electrical / Combination Meter / Data List.

    6. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      Auto High Beam Main Switch Auto high beam switch signal / OFF or ON

      OFF: Auto high beam switch off

      ON: Auto high beam switch on

      		 -
      Dimmer SW Headlight dimmer switch High position signal / OFF or ON

      OFF: Headlight dimmer switch not in High position

      ON: Headlight dimmer switch in High position

      		 -
      Passing Light SW Headlight dimmer switch Flash position signal / OFF or ON

      OFF: Headlight dimmer switch not in Flash position

      ON: Headlight dimmer switch in Flash position

      		 -
      Rear Fog Light SW Fog light switch rear position signal / OFF or ON

      OFF: Fog light switch off

      ON: Fog light switch in rear position

      		 w/ Rear Fog Light
      Front Fog Light SW Fog light switch front position signal / OFF or ON

      OFF: Fog light switch off

      ON: Fog light switch in front position

      		 w/ Front Fog Light
      Auto Light SW Light control switch Auto position signal / OFF or ON

      OFF: Light control switch not in Auto position

      ON: Light control switch in Auto position

      		 -
      Head Light SW (Head) Light control switch Head position signal / OFF or ON

      OFF: Light control switch not in Head position

      ON: Light control switch in Head position

      		 -
      Head Light SW (Tail) Light control switch Tail position signal / OFF or ON

      OFF: Light control switch not in Tail position

      ON: Light control switch in Tail position

      		 -
      Insolation Amount of Solar Sensor RH Light control sensor RH condition / Min.: 0, Max.: 51100 or Sensor Fail Condition can be displayed Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Insolation Amount of Solar Sensor LH Light control sensor LH condition / Min.: 0, Max.: 51100 or Sensor Fail Condition can be displayed Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Light Sensor Illuminance Light control sensor illuminance / 0 to 8191 lx Value is output according to ambient light level -
      AUTO Light Status AUTO headlight status / Not AUTO or AUTO Current control status -
      Light Sensor Connection Status Connection status to automatic light control sensor / OFF or ON

      OFF: Not Connected

      ON: Connected

      		 -
      Headlight Lighting Function ECU which controls the lighting system / Main Body or Lighting Sys ECU

      Main Body: Lighting system controlled by main body ECU (multiplex network body ECU)

      Lighting Sys ECU: Lighting system is controlled by No. 1 headlight ECU sub-assembly

      		 -
      Auto H Beam STS0 Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* -
      Auto H Beam STS1 Automatic high beam sensor state past 1 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS2 Automatic high beam sensor state past 2 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS3 Automatic high beam sensor state past 3 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS4 Automatic high beam sensor state past 4 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS5 Automatic high beam sensor state past 5 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS6 Automatic high beam sensor state past 6 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      Auto H Beam STS7 Automatic high beam sensor state past 7 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err Condition can be displayed* Although the item is displayed on the GTS, it is not applicable to the vehicle.
      The Number of DTC Number of trouble codes / 0 to 255 Number of stored DTCs displayed -

      Tech Tips

      *: The details of each value of the Control Range are as follows:

      Range Condition Control Condition Diagnostic Note
      Undetec Automatic high beam sensor being initialized Control suspended (low beam headlights illuminated) -
      CAM NA Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. Control suspended (low beam headlights illuminated) -
      No sens No lights detected High beam headlights illuminated Only when vehicle speed within operation speed range
      Hlight Headlights of oncoming vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Taillgt Taillights preceding vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Speed No lights detected and vehicle speed below operation speed Low beam headlights illuminated -
      Daytime Bright light detected Low beam headlights illuminated -
      Village Streetlights, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
      Delay Changing between low beams and high beams Changing between low beams and high beams Only when vehicle speed within operation speed range
      Malfunc Not applicable - -
      Aim Lmt
      SAE Mod
      Undefin
      LIN Err
      AFS
      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      Clearance Light State Clearance light state / OFF or ON

      OFF: Clearance lights off

      ON: Clearance lights on

      		 -
      +B Voltage Value No. 1 headlight ECU sub-assembly LH +B power supply voltage value / Min.: 0 V, Max.: 19.75 V 11 to 14 V -
      Headlight Low Beam State Low beam headlight state / OFF or ON

      OFF: Low beam headlights off

      ON: Low beam headlights on

      		 -
      Headlight High Beam State High beam headlight state / OFF or ON

      OFF: High beam headlights off

      ON: High beam headlights on

      		 -
      DRL State Daytime running light state / OFF or ON

      OFF: Daytime running lights off

      ON: Daytime running lights on

      		 -
      Engine Engine condition / Run or Stop

      Run: Engine running

      Stop: Engine stopped

      		 -
      Rr Height Sens Signal Val Rear height control sensor sub-assembly RH power supply value / Min.: 0 V, Max.: 6.25 V 0.50 to 4.50 V Value changes according to vehicle height
      Rear Height Sensor Value Rear height control sensor sub-assembly RH signal value / Min.: -128 mm, Max.: 127 mm Condition can be displayed -
      +B No. 1 headlight ECU sub-assembly LH IG power supply voltage value / Min.: 0 V, Max.: 19.75 V 11 to 14 V -
      FR Wheel Speed Front right wheel speed / Min.: 0 km/h (0 mph), Max.: 260 km/h (162 mph)

      Actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      		 -
      FL Wheel Speed Front left wheel speed / Min.: 0 km/h (0 mph), Max.: 260 km/h (162 mph)

      Actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      		 -
      Vehicle Speed Vehicle speed / Min.: 0 km/h (0 mph), Max.: 260 km/h (162 mph)

      Actual vehicle speed

      Vehicle stopped: 0 km/h (0 mph)

      		 -
      Rear Height Adjust Value Rear height adjustment off set value / Min.: 0, Max.: 65535 Actual rear height adjustment normal value is displayed (If there is a malfunction, no value is displayed) -
      Rear Height Adjust Valid Flag Rear height adjustment range / Valid or Invalid

      Valid: Rear height control sensor sub-assembly RH value within normal range

      Invalid: Rear height control sensor sub-assembly RH value out of normal range

      		 -
      Init Writing Count Number of times initialization performed / 0 to 255 Number of times initialization performed -
      Sensor Initialization Hist Sensor initialization history / not comp, 10%, 25%, 50%, 75%, 100% or completed

      not comp: Headlight ECU sub-assembly LH not initialized after replacing.

      10%: Initialization completed when fuel tank was 10% full

      25%: Initialization completed when fuel tank was 25% full

      50%: Initialization completed when fuel tank was 50% full

      75%: Initialization completed when fuel tank was 75% full

      100%: Initialization completed when fuel tank was 100% full

      completed: ECU not replaced and ECU has not been initialized at workshop.

      		 -
      LR Leveling Target Step Headlight leveling motor LH and RH (leveling portion) current step value / Min.: 0 step, Max.: 500 step 7 to 247 step -
      L Leveling Current Step Headlight leveling motor LH (leveling portion) current step value / Min.: 0 step, Max.: 500 step 7 to 247 step -
      R Leveling Current Step Headlight leveling motor RH (leveling portion) current step value / Min.: 0 step, Max.: 500 step 7 to 247 step -
      The Number of DTC Number of trouble codes / 0 to 255 Number of stored DTCs displayed -
      Combination Meter
      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      Turn Signal Switch (Right) Turn signal switch (right) signal / OFF or ON

      OFF: Turn signal switch not in right turn position

      ON: Turn signal switch in right turn position

      		 -
      Turn Signal Switch (Left) Turn signal switch (left) signal / OFF or ON

      OFF: Turn signal switch not in left turn position

      ON: Turn signal switch in left turn position

      		 -
      Turn Switch Signal (Full Turn) Turn signal switch signal / OFF or ON

      OFF: Turn signal switch off

      ON: Turn signal switch on (Full Turn)

      		 Displays for both right and left turns.
      Hazard Flasher Switch Integration control and panel assembly (hazard warning signal switch) / OFF or ON

      OFF: Integration control and panel assembly (hazard warning signal switch) off

      ON: Integration control and panel assembly (hazard warning signal switch) on

      		 -
      Lane Change Flashing Times Setting Condition of the lane change flashing times / OFF, 3, 4, 5, 6 or 7 Customized value displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus:


      1. Body Electrical / Main Body / Active Test.

      2. Body Electrical / AFS / Active Test.

      3. Body Electrical / Combination Meter / Active Test.

    6. Perform the Active Test according to the display on the GTS.

      Main Body
      Tester Display Measurement Item Normal Condition Diagnostic Note
      Daytime Running Light Daytime running lights OFF or ON -
      Taillight Relay Taillights and license plate light OFF or ON -
      Headlight Low beam headlights OFF or ON -
      Head Light Hi High beam headlights OFF or ON -
      Front Fog Light Relay Front fog lights OFF or ON w/ Front Fog Light
      Rear Fog Light Relay Rear fog lights OFF or ON

      • w/ Rear Fog Light

      • Light control switch in Tail or Head position.
      AFS
      Tester Display Measurement Item Normal Condition Diagnostic Note
      Drive The Leveling Motor Headlight leveling motor operation Stop/Down/Up Perform the Active Test with the engine started and vehicle stopped
      Clearance Light Clearance lights OFF or ON -
      Headlight Low Beam Low beam headlights OFF or ON -
      Headlight High Beam High beam headlights OFF or ON -
      Daytime Running Light Daytime running lights OFF or ON -
      Headlight Indicator "HEADLIGHT SYSTEM MALFUNCTION VISIT YOUR DEALER" display OFF or ON -
      Headlight Leveling Indicator Headlight beam level control warning light OFF or ON -
      Combination Meter
      Tester Display Measurement Item Control Range Diagnostic Note
      Automatic High Beam Indicator Automatic high beam indicator light OFF or ON w/ Automatic High Beam System