OUTER REAR VIEW MIRROR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the and LH sides.

  • The procedure listed below is for the LH side.

  • w/ Multi-terrain Monitor System:

    When removing only the side television camera assembly, refer to TELEVISION CAMERA (for Side).

    Click here

PROCEDURE


  1. REMOVE OUTER MIRROR GLASS

    Click here

  2. REMOVE OUTER MIRROR COVER LH

    B001DXRN05

    Tech Tips

    Be sure to detach the claws of the outer mirror cover LH in the order shown in the illustration.


    1. B001CL0C01
      *a Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover LH.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      B001FT3C03
      *a Protective Tape *b Rib
      *c Inner Side of Outer Mirror Cover - -
    3. B001HPKC02
      *a Protective Tape

      Put protective tape around the outer mirror cover LH and outer mirror body.

    4. Insert moulding remover A into the space made between the outer mirror body and outer mirror cover LH.

      Note

      Do not insert the moulding remover A more than 4 mm (0.157 in.).

    5. B001HVQC08
      *a 40.0 mm (1.57 in.)

      Slide the moulding remover A downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover A more than 4 mm (0.157 in.).

      • Do not slide the moulding remover A past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover LH as the outer mirror body will become LH damaged.

    6. Remove the moulding remover A.

    7. B001CQ4C02
      *a Protective Tape

      Put protective tape around the outer mirror cover LH and outer mirror body.

    8. Insert moulding remover A between the outer mirror cover LH and outer mirror body as shown in the illustration and detach the claw.

    9. B001CYHC06
      *a Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    10. B001EUL

      Detach the 2 claws and remove the outer mirror cover LH.

      Note

      When removing the outer mirror cover LH, be careful not to damage the side turn signal light assembly LH.

  3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

    Click here

  4. REMOVE OUTER MIRROR RETRACTOR LH (w/o Reverse Shift-linked Mirror)


    1. Remove the outer rear view mirror gasket LH.


      1. B001HOCC01
        *a Cut here

        Cut the wire harness sub-assembly at the location shown in the illustration.

        Tech Tips

        A new wire harness sub-assembly is used for reassembly.

      2. B001GZWC01
        *a Tape
        *b Clamp

        Remove the tape and detach the clamp.

    2. B001GUD

      Remove the screw.

    3. Detach the 5 claws and remove the outer rear view mirror gasket LH.

    4. Remove the lower mirror cover.


      1. B001FVTC03
        *a Protective Tape
        B001GQDN01

        Put protective tape around the lower mirror cover.

        Tech Tips

        The claws of the mirror will be detached in the order shown in the illustration in the following steps.

      2. B001GVYC01
        *a Protective Tape

        Using a screwdriver, detach the claw.

        Tech Tips

        Tape the screwdriver tip before use.

      3. B001HGPC01
        *a Protective Tape

        Using a screwdriver, detach the claw.

      4. B001FP2C01
        *a Protective Tape

        Using a screwdriver, detach the claw to create a space between the lower mirror cover and outer mirror body as shown in the illustration.

      5. B001CG2C03
        *a Protective Tape

        Insert a screwdriver as shown in the illustration.

      6. B001FMKC03
        *a Protective Tape

        Detach the claw to create a space between the lower mirror cover and cover base as shown in the illustration.

      7. B001GWF

        While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 2 claws and remove the lower mirror cover.

    5. B001FZJ

      Using a T25 "TORX" socket wrench, remove the 3 "TORX" screws.

    6. Remove the cover base.

    7. B001E9N

      Remove the 5 screws and outer mirror body.

    8. B001CXSC01
      *a Guide

      Detach the guide and remove the cover body.

      Note

      Be careful as the guide shown in the part of the illustration is easily damaged.

    9. Remove the outer mirror actuator assembly LH.


      1. B001HH9C01
        *a Cover

        Slide the cover as shown in the illustration and disconnect the connector.

      2. B001HTJ

        Pull out the wire harness sub-assembly in the direction indicated by the arrow in the illustration.

      3. B001FWS

        Remove the 3 screws and outer mirror actuator assembly LH.

      4. B001HFT

        Detach the 2 clamps and open the cover.

      5. B001HUX

        Disconnect the connector and remove the outer mirror actuator assembly LH.

    10. Remove the support spring.


      1. B001HQK

        Remove the 2 screws, and then detach the 6 claws and remove the 2 support springs.

  5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)

    Click here