OUTER REAR VIEW MIRROR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the and LH sides.

  • The procedure listed below is for the LH side.

  • w/ Side Monitor System:

    When installing only the side television camera assembly, refer to TELEVISION CAMERA (for Side) Click here.

PROCEDURE


  1. REMOVE OUTER REAR VIEW MIRROR GLASS

    Click here

  2. REMOVE OUTER MIRROR COVER LH

    A01XJQME09

    Tech Tips

    Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


    1. A01XKF2E01
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      A01XCYVE07
      Text in Illustration
      *1 Protective Tape *2 Rib
      *a Inner Side of Outer Mirror Cover - -
    3. A01XIM7E01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Tech Tips

      Tape the moulding remover before use.

    4. A01XCUUE01

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Standard
      Area Specified Condition
      a 40.0 mm (1.57 in.)

    5. Remove the moulding remover.

    6. A01XINTE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

    7. A01XK30E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

    8. B001EUL

      Detach the 2 claws and remove the outer mirror cover.

      Note

      When removing the cover, be careful not to damage the side turn signal light assembly or cover.

  3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

    Click here

  4. REMOVE OUTER MIRROR RETRACTOR LH


    1. Remove the outer rear view mirror gasket LH.


      1. A01XM3RE01
        Text in Illustration
        *a Cut here

        Cut the wire harness sub-assembly at the location shown in the illustration.

        Tech Tips

        A new wire harness sub-assembly is used for reassembly.

      2. A01XH6ZE01
        Text in Illustration
        *1 Tape
        *2 Clamp

        Remove the tape and detach the clamp.

    2. B001GUD

      Remove the screw, detach the 5 claws and remove the outer rear view mirror gasket LH.

    3. Remove the lower mirror cover.


      1. A01XCHNE01
        A01XJBCE01

        Put protective tape around the lower mirror cover.

        Text in Illustration
        *1 Protective Tape

        Tech Tips

        The claws of the mirror will be detached in the order shown in the illustration in the following steps.

      2. A01XJQNE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      3. A01XHSPE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      4. A01XIE2E05
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      5. A01XJROE01
        Text in Illustration
        *1 Protective Tape

        Insert a screwdriver as shown in the illustration.

      6. A01XGXNE01
        Text in Illustration
        *1 Protective Tape

        Detach the claw to create a space between the lower mirror cover and cover base as shown in the illustration.

      7. A01XFX3

        While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 3 claws and remove the lower mirror cover.

    4. B001FZJ

      Using a T25 "TORX" socket wrench, remove the 3 screws.

    5. A01XIURE01
      Text in Illustration
      *1 Protective Tape

      w/ Side Monitor System:


      1. Remove the connector from the wire clip.

      2. Disconnect the connector.

        Note

        When disconnecting the connector, be careful not to damage it.

    6. B001E9N

      Remove the 5 screws and outer mirror body.

    7. A01XKCSE01
      Text in Illustration
      *a A

      Detach the claw and remove the cover body.

      Note

      Be careful as the claw shown in the part of the illustration labeled A is easily damaged.

    8. Remove the actuator sub-assembly.


      1. A01XDPV

        Slide the cover as shown in the illustration and disconnect the connector.

      2. A01XCWBE02

        Pull out the wire harness sub-assembly in the direction indicated by the arrow in the illustration.

      3. B001FWS

        Remove the 3 screws and actuator sub-assembly.

      4. A01XLSS

        Detach the clamp.

      5. Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the two claws and disconnect the connector.

    9. w/ Side Monitor System:


      1. A01XJRN

        Detach the claw and remove the wire clip.

    10. Remove the support spring.


      1. B001HQK

        Remove the 2 screws, and then detach the 6 claws and remove the 2 support springs.

  5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)


    1. Remove the side television camera assembly Click here.