POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) Reverse Shift-linked Function of Power Mirrors does not Operate

DESCRIPTION

ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Each outer mirror control ECU assembly then performs control in response to the reverse signal.

WIRING DIAGRAM

B001I8YE01

CAUTION / NOTICE / HINT

Note


  • First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

  • As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

    *: w/ Door Control Battery

Tech Tips

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).

PROCEDURE


  1. CHECK MEMORY AND REACTIVATION FUNCTION


    1. Turn the ignition switch to ON.

    2. Using the multiplex network master switch assembly, turn the mirror surface to the fully left position.

    3. Press the M1 switch while the SET switch is being pressed.

    4. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

    5. Using the multiplex network master switch assembly, turn the mirror surface to the fully right position.

    6. Press the M1 switch.

    7. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.

      Result
      Result Proceed to
      Memory and reactivation functions are normal A
      Memory function is not normal B
      Reactivation function is not normal C

    B

    GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror Surface Position is not Memorized) Click here

    C

    GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirrors do not Return to Memorized Position) Click here

    A

  2. CHECK FOR DTC (SFI SYSTEM, ECD SYSTEM)


    1. Check for DTCs.


      OK
      DTCs output does not occur.
      Result
      Result Proceed to
      OK A
      NG (for 1GR-FE) B
      NG (for 1KD-FTV) C
      NG (for 1GD-FTV) D
      NG (for 1GD-FTV [w/ Urea SCR System]) E

    B

    GO TO SFI SYSTEM Click here

    C

    GO TO ECD SYSTEM Click here

    D

    GO TO ECD SYSTEM Click here

    E

    GO TO ECD SYSTEM Click here

    A

  3. CHECK SHIFT POSITION INDICATOR FUNCTION


    1. Check that the shift position indicator operates.

      Click here

      OK
      Shift position indicator operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  4. CONFIRM MALFUNCTIONING PARTS


    1. Check the malfunctioning outer rear view mirror assembly.

      Click here

      Result
      Result Proceed to
      Both the left and right outer rear view mirror assemblies do not operate A
      Outer rear view mirror assembly LH does not operate B
      Outer rear view mirror assembly RH does not operate C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH Click here

    B

  5. CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

      Click here

    2. Check that the reverse shift-linked function operates.

      Click here

      OK
      Reverse shift-linked function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here

  6. CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH


    1. Temporarily replace the outer rear view mirror assembly RH with a new or normally functioning one.

      Click here

    2. Check that the reverse shift-linked function operates.

      Click here

      OK
      Reverse shift-linked function operates normally.
      Result
      Proceed to
      OK
      NG

    OK

    END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

    NG

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH Click here