READ DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Open Switch | Slide open switch signal / ON or OFF | ON: Slide open switch pressed OFF: Slide open switch not pressed |
- |
| Close Switch | Slide close switch signal / ON or OFF | ON: Slide close switch pressed OFF: Slide close switch not pressed |
- |
| Up Switch | Tilt up switch signal / ON or OFF | ON: Tilt up switch pressed OFF: Tilt up switch not pressed |
- |
| Down Switch | Tilt down switch signal / ON or OFF | ON: Tilt down switch pressed OFF: Tilt down switch not pressed |
- |
| Hall IC1 Pulse | Hall IC1 pulse output / Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low. Hi: Hall IC1 output is high. |
| Hall IC1 Status | Status of Hall IC1 / Normal or Error | Normal: Hall IC1 normal Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output / Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low. Hi: Hall IC2 output is high. |
| Hall IC2 Status | Status of Hall IC2 / Normal or Error | Normal: Hall IC2 normal Error: Hall IC2 not normal |
- |
| Ignition (Direct Signal) | Ignition switch signal / ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
- |
| Ignition (MPX) | Ignition switch signal (LIN signal) / ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
- |
| Door Courtesy | Driver side door courtesy light switch signal / ON or OFF | ON: Driver side door open OFF: Driver side door closed |
- |
| Door Key Close Operation | Key-linked sliding roof close signal / ON or OFF | ON: Driver side door key cylinder turned to lock position using key OFF: Driver side door key cylinder not turned |
- |
| Door Key Open Operation | Key-linked sliding roof open signal / ON or OFF | ON: Driver side door key cylinder turned to unlock position using key OFF: Driver side door key cylinder not turned |
- |
| Wireless Close Operation | Wireless sliding roof close signal / ON or OFF | ON: Transmitter LOCK switch pressed and held OFF: Transmitter LOCK switch not pressed |
- |
| Wireless Open Operation | Wireless sliding roof open signal / ON or OFF | ON: Transmitter UNLOCK switch pressed and held OFF: Transmitter UNLOCK switch not pressed |
- |
| Key Off Permission | Key-off operation permit signal / ON or OFF | ON: Driver side door not closed within 43 seconds after ignition switch turned off OFF: Any status except "ON" status |
- |
| Door Key Related (Open) | Key-linked sliding roof open operation status / Avail or Not Avl | Avail: Key-linked sliding roof open operation available Not Avl: Key-linked sliding roof open operation not available |
Customize function. |
| Door Key Related (Close) | Key-linked sliding roof close operation status / Avail or Not Avl | Avail: Key-linked sliding roof close operation available Not Avl: Key-linked sliding roof close operation not available |
Customize function. |
| Wireless Key Rel (Open) | Wireless transmitter-linked sliding roof open operation status / Avail or Not Avl | Avail: Wireless transmitter-linked sliding roof open operation available Not Avl: Wireless transmitter-linked sliding roof open operation not available |
Customize function. |
| Wireless Key Rel (Close) | Wireless transmitter-linked sliding roof close operation status / Avail or Not Avl | Avail: Wireless transmitter-linked sliding roof close operation available Not Avl: Wireless transmitter-linked sliding roof close operation not available |
Customize function. |
| Door Key Related Operation | Direction for key-linked operation / Tilt or Slide | Tilt: Key-linked sliding roof operation operates tilt up or down Slide: Key-linked sliding roof operation operates slide open or close |
Customize function. |
| Wireless Key Rel Operation | Direction for wireless transmitter-linked operation / Tilt or Slide | Tilt: Wireless transmitter-linked sliding roof operation operates tilt up or down Slide: Wireless transmitter-linked sliding roof operation operates slide open or close |
Customize function. |
| Open Switch Failure (Past) | Slide open switch failure signal (Past) / ON or OFF | ON: Slide open switch signal failure (Past) OFF: No slide open switch signal failure (Past) |
- |
| Close Switch Failure (Past) | Slide close switch failure signal (Past) / ON or OFF | ON: Slide close switch signal failure (Past) OFF: No slide close switch signal failure (Past) |
- |
| Up Switch Failure (Past) | Tilt up switch failure signal (Past) / ON or OFF | ON: Tilt up switch signal failure (Past) OFF: No tilt up switch signal failure (Past) |
- |
| Down Switch Failure (Past) | Tilt down switch failure signal (Past) / ON or OFF | ON: Tilt down switch signal failure (Past) OFF: No tilt down switch signal failure (Past) |
- |
| Open Switch Failure (Current) | Slide open switch failure signal (Current) / ON or OFF | ON: Slide open switch signal failure (Current) OFF: No slide open switch signal failure (Current) |
- |
| Close Switch Failure (Current) | Slide close switch failure signal (Current) / ON or OFF | ON: Slide close switch signal failure (Current) OFF: No slide close switch signal failure (Current) |
- |
| Up Switch Failure (Current) | Tilt up switch failure signal (Current) / ON or OFF | ON: Tilt up switch signal failure (Current) OFF: No tilt up switch signal failure (Current) |
- |
| Down Switch Failure (Current) | Tilt down switch failure signal (Current) / ON or OFF | ON: Tilt down switch signal failure (Current) OFF: No tilt down switch signal failure (Current) |
- |
| Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 | Number of DTCs displayed | - |
PERFORM ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Sliding Roof / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof | Opn/Dwn: Sliding roof slide open or tilt down operation occurs Clos/Up: Sliding roof slide close or tilt up operation occurs OFF: Sliding roof is not operating |
- |