BACK DOOR GLASS(w/ Back Door Tire Carrier) REMOVAL

PROCEDURE


  1. REMOVE BACK DOOR CENTER GARNISH

    Click here

  2. REMOVE BACK DOOR SIDE GARNISH LH

    Click here

  3. REMOVE BACK DOOR SIDE GARNISH RH

    Click here

  4. REMOVE BACK DOOR TRIM COVER

    Click here

  5. REMOVE UPPER TOOL BOX PANEL SUB-ASSEMBLY

    Click here

  6. REMOVE TOOL CASE

    Click here

  7. REMOVE BACK DOOR INSIDE HANDLE BEZEL (for Face to Face Seat Type)

    Click here

  8. REMOVE BACK DOOR TRIM PANEL ASSEMBLY

    Click here

  9. REMOVE BACK DOOR INSIDE HANDLE SUB-ASSEMBLY (for Face to Face Seat Type)

    Click here

  10. REMOVE SPARE WHEEL COVER PAD

    Click here

  11. REMOVE SPARE WHEEL COVER

    Click here

  12. REMOVE SPARE TIRE

  13. REMOVE NO. 2 SPARE WHEEL COVER

    Click here

  14. REMOVE REAR SPOILER COVER RH

    Click here

  15. REMOVE REAR SPOILER SUB-ASSEMBLY

    Click here

  16. REMOVE REAR WIPER ARM

    Click here

  17. REMOVE REAR WIPER MOTOR ASSEMBLY

    Click here

  18. REMOVE NO. 1 BACK WINDOW WIPER MOTOR BRACKET

    Click here

  19. REMOVE BACK WINDOW OUTSIDE MOULDING


    1. Using a knife, cut off the 2 outside mouldings as shown in the illustration.

      Note


      • Do not damage the vehicle body with the knife.

      • If the vehicle body is damaged, repair the damaged portion by applying an anti-rust coating after removing the back window glass assembly.

      A01XDLGE02
      Text in Illustration
      *1 Cut - -

    2. Remove the remaining outside moulding from the back door glass.

  20. REMOVE BACK DOOR GLASS

    A01XKBQE01

    1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note

      When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      Text in Illustration
      *1 Protective Tape

    2. Disconnect the connectors.

    3. A01XIM9E02
      Text in Illustration
      *1 Clip
      *2 Adhesive Dam

      From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    4. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    5. Cut off the adhesive by pulling the piano wire around the back window glass.

      Note


      • When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      • Leave as much adhesive on the vehicle body as possible when removing the back window glass.

    6. A01XK2QE01
      Text in Illustration
      *a Matchmark

      Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

      Tech Tips

      Matchmarks do not need to be placed if the glass is not going to be reused.

    7. A01XJHY

      Using suction cups, remove the back door glass.

      Note

      Be careful not to drop the back door glass.

  21. REMOVE BACK WINDOW GLASS CLIP LH


    1. A01XD8S

      Using a scraper, remove the clip.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the clip with new one.

  22. REMOVE BACK WINDOW GLASS CLIP RH


    1. A01XIO6

      Using a scraper, remove the clip.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the clip with new one.

  23. REMOVE BACK DOOR GLASS ADHESIVE DAM


    1. A01XGZP

      Using a scraper, remove the 2 dams.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the 2 dams with new ones.

  24. REMOVE BACK WINDOW UPPER OUTSIDE MOULDING


    1. A01XFEGE01
      Text in Illustration
      *1 Back Window Upper Outside Moulding LH
      *2 Back Window Upper Outside Moulding RH

      Using a scraper, remove the outside moulding LH and RH.

      Note


      • Be careful not to damage the back door glass.

      • Be sure to replace the mouldings with new ones.