ROOF HEADLINING(for 5 Door) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. for Manual Seat Type:

      Remove the rear No. 2 seat assembly Click here.

    2. for Power Seat Type:

      Remove the rear No. 2 seat assembly Click here.

    3. for Face to Face Seat Type:

      Remove the rear No. 2 seat assembly Click here.

  4. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Slide Walk-in Seat Type LH Side:

      Remove the rear No. 1 seat assembly Click here.

    2. for 60/40 Split Slide Walk-in Seat Type RH Side:

      Remove the rear No. 1 seat assembly Click here.

  5. REMOVE REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Double-folding Seat Type LH Side:

      Remove the rear No. 1 seatback assembly Click here.

    2. for 60/40 Split Double-folding Seat Type RH Side:

      Remove the rear No. 1 seatback assembly Click here.

  6. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    A01XK1XE07
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE COWL SIDE TRIM BOARD LH

    B001C83

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  9. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B001HKE

    1. Remove the front door opening trim weatherstrip.

  11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

    A01XDWZE02
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front No. 1 assist grip plug.


    1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  13. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE NO. 1 ASSIST GRIP

    B001CRR

    Tech Tips

    Use the same procedure for the other No. 1 assist grip.


    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 1 assist grip.

  15. REMOVE FRONT PILLAR GARNISH LH

    B001H4V

    1. Detach the 3 guides and remove the front pillar garnish.

    2. A01XDZDE02
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  16. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    A01XJCIE05
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all rear No. 1 floor step covers.


    1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

      Tech Tips

      Tape the screwdriver tip before use.

  18. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

    B001GY3

    1. Remove the 2 bolts and quarter scuff plate.

  19. REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE REAR DOOR SCUFF PLATE LH

    A01XJ2TE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate.

    2. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  21. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B001I48

    1. Remove the rear door opening trim weatherstrip.

  23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE OUTER LAP BELT ANCHOR COVER

    B001CVN

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  25. REMOVE LOWER CENTER PILLAR GARNISH LH

    B001DOC

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. B001GNR

      Detach the 4 claws and 2 clips and remove the lower center pillar garnish.

  26. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. REMOVE NO. 2 ASSIST GRIP PLUG LH

    A01XFAHE04
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front No. 2 assist grip plug.


    1. Using a screwdriver, detach the 2 claws and remove the front No. 2 assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  28. REMOVE NO. 2 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  29. REMOVE NO. 2 ASSIST GRIP

    B001EUQ

    Tech Tips

    Use the same procedure for the other No. 2 assist grip.


    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 2 assist grip.

  30. REMOVE CENTER PILLAR GARNISH LH

    B001GI8

    1. Move the front shoulder belt anchor adjuster to the lowest position.

    2. Remove the bolt.

    3. Detach the 2 clips and 2 guides.

    4. Pass the front seat outer belt floor anchor through the center pillar garnish and remove the center pillar garnish.

  31. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  33. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    B001GEG

    Tech Tips

    Use the same procedure for the other front luggage compartment trim cover.


    1. Detach the 4 claws and remove the cap.

    2. A01XH2WE02
      Text in Illustration
      *1 Luggage Hold Belt Striker

      Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

  34. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    B001F7R

    1. Detach the clip and remove the No. 1 deck board.

  35. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

    B001FNO

    1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.

  36. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    B001GEV

    1. Remove the 3 bolts and floor side rail.

  37. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  38. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)


    1. Detach the 4 claws and remove the rear floor carpet.

      A01XJK3E01
      Text in Illustration
      *A w/o Deck Rail *B w/ Deck Rail
      *C for Face to Face Seat Type - -

  39. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    B001D32

    Tech Tips

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


    1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.

  40. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    B001FL1

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  41. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    A01XHVNE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other No. 1 tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  42. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    A01XHKOE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  43. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    A01XF68E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  44. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    B001GRR

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Remove the 2 bolts and assist grip.

  45. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat:


      1. B001IJX

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B001GI3

        Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

      3. Remove the 4 bolts and 2 screws.

      4. Detach the 5 clips and 8 claws.

      5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

        B001H9K

    2. w/ Rear No. 2 Seat:


      1. B001IJX

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B001FVL

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and 2 screws.

      4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

        B001EKP

  46. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. w/o Rear No. 2 Seat:


      1. B001GZ7

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B001CJS

        Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

      3. Remove the 4 bolts and screws.

      4. Detach the 5 clips and 8 claws.

      5. Disconnect each connector.

      6. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

        B001FVI

    2. w/ Rear No. 2 Seat:


      1. B001GZ7

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. B001FCB

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and screw.

      4. Detach the 4 clips and 8 claws.

      5. Disconnect each connector and remove the deck trim side panel.

        B001GIN

  47. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B001FC9

    1. Move the rear shoulder belt anchor adjuster to the lowest position.

    2. Detach the 2 clips and 2 guides.

    3. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

  48. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

    B001CHH

    1. w/o Rear No. 2 Seat:


      1. Detach the 7 clips and 2 guides and remove the rear quarter trim panel.

    2. B001GO9

      w/ Rear No. 2 Seat:


      1. Detach the 7 clips and 2 guides.

      2. B001IMI

        Detach the 4 clips and 2 guides, pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

  50. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A01XJJRE03
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  52. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A01XIEDE03
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  53. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  54. REMOVE ASSIST GRIP (w/ Rear No. 2 Seat)

    A01XGCLE03

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a screwdriver, detach the 4 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. B001GF2

      Remove the 2 bolts and assist grip.

  55. REMOVE VISOR BRACKET COVER LH

    B001E7V

    Tech Tips

    Use the same procedure for the other visor bracket cover.


    1. Detach the 4 claws and remove the visor bracket cover.

  56. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  57. REMOVE VISOR ASSEMBLY LH

    B001CWP

    1. Remove the 2 screws and visor.

  58. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  59. REMOVE VISOR HOLDER

    B001IEAE02

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  60. REMOVE MAP LIGHT ASSEMBLY

    Click here

  61. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  62. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  63. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. Remove the No. 1 room light assembly Click here.

  64. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. Remove the No. 2 room light assembly Click here.

  65. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

    Click here

  66. REMOVE REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)

    Click here

  67. REMOVE REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)

    Click here

  68. REMOVE ROOF HEADLINING ASSEMBLY

    A01XGE5

    1. w/ EC Mirror:

      Disconnect the inner mirror connector.

    2. B001CS9

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. B001HKW

      w/ Sliding Roof:

      Disconnect the drive gear connector.

    4. B001DJG

      w/ Digital Audio Broadcasting Antenna:

      Disconnect the connector and detach the wire harness clamp.

    5. B001I2R

      Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

    6. B001DAD

      Remove the bolt.

    7. Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

    8. B001DQV

      Disconnect the 2 connectors and detach the clamp from the rear pillar LH.

    9. B001EOS

      Disconnect the connector and detach the 3 clamps from the rear pillar RH.

    10. B001FQ4

      w/ Rear Seat Entertainment System:

      Disconnect the 2 connectors.

    11. B001D5P

      w/o Sliding Roof:


      1. Detach the 2 clips.

    12. A01XLIZE03
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Sliding Roof:


      1. Detach the 2 clips, 2 guides and 8 fasteners.

    13. A01XCU3E03
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Rear Seat Entertainment System:


      1. Detach the 2 clips, 2 guides and 6 fasteners.

    14. B001D90

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when removing it.

  69. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001GHB

    1. Detach the 5 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.

  70. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  71. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001GHV

    1. Detach the 6 claws of the rear shoulder belt anchor plate and slide the rear shoulder belt anchor plate in the direction of the arrow to remove it.

  72. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  73. REMOVE NO. 1 ROOF SIDE RAIL GARNISH LH


    1. A01XCBTE01
      Text in Illustration
      *1 Cut Off Position

      Detach the 3 clips.

    2. Cut off the 3 clips and remove the roof side rail garnish.

    3. Remove 3 clips from the vehicle body.

  74. REMOVE NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  75. REMOVE ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)

    B001CQN

    1. Detach the 4 claws and 2 guides and remove the roof side inner garnish cap.

  76. REMOVE ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  77. REMOVE REAR SEAT SHOULDER BELT HANGER LH

    B001H1C

    1. Detach the claw and guide and remove the rear seat shoulder belt hanger.

  78. REMOVE REAR SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedure described for the LH side.

  79. REMOVE QUARTER TRIM COVER

    B001GN9

    Tech Tips

    Use the same procedure for the other quarter trim cover.


    1. Detach the 2 claws and remove the quarter trim cover.

  80. REMOVE QUARTER TRIM JACK COVER

    B001FJ4

    1. Detach the 3 claws and 2 guides and remove the quarter trim jack cover.

  81. REMOVE DECK SIDE TRIM COVER LH

    B001IJS

    1. Detach the 3 claws and 2 guides and remove the deck side trim cover.

  82. REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    B001D62

    1. Detach the 2 claws and remove the rear side rail spacer.

  83. REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  84. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

    B001FTD

    1. Detach the 2 claws and remove the rear No. 2 side rail spacer.

  85. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  86. REMOVE REAR NO. 3 SIDE RAIL SPACER LH

    B001GV9

    1. Detach the 2 claws and remove the rear No. 3 side rail spacer.

  87. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.