REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note


  • Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is replaced with a new one.

    • Initialization (initial position reset) of the fold seat control ECU is performed.


  • Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is exchanged with one from another vehicle.

    • The seatback frame and seat leg are inspected.

    • The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

    • The seatback frame or seat leg is replaced.

    • The cable is disconnected from the battery while the seatback or seat cushion is operating.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE CAP


    1. A01XDXR

      Remove the 2 caps.

  2. REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH


    1. A01XMCI

      Remove the 2 screws.

    2. Detach the 3 claws and remove the cover.

  3. REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH


    1. A01XEQ4E01
      Text in Illustration
      *1 Guide

      Remove the 2 screws.

    2. Detach the 2 claws and guide and remove the cover.

  4. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

    Click here

  5. REMOVE FOLD SEAT CONTROL ECU

    Click here

  6. REMOVE REAR SEAT NO. 1 CUSHION MOULDING


    1. A01XLKIE01
      Text in Illustration
      *1 Guide

      Using a clip remover, remove the 2 clips.

    2. Detach the 2 claws and 4 guides and remove the moulding.

  7. REMOVE SEAT CUSHION COVER WITH PAD


    1. A01XD0RE01
      Text in Illustration
      *1 Fastener

      Open the 2 fasteners.

    2. A01XCDF

      Remove the 2 clips and open the under part of the seat cushion cover.

    3. A01XJBSE01
      Text in Illustration
      *1 Hook

      Detach the 2 hooks and remove the seat cushion cover with pad.

  8. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH


    1. A01XGIRE01
      Text in Illustration
      *1 Fastener

      Detach the fastener.

    2. Remove the hog rings and seat cushion cover.

  9. REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH


    1. A01XIXZE01
      Text in Illustration
      *1 Tack Pin

      Cut off the tack pins and remove the protector from the cushion pad.

  10. REMOVE REAR SEAT NO. 2 CUSHION MOULDING


    1. A01XKEQ

      Remove the 2 screws.

    2. Detach the 2 claws and remove the moulding.

  11. REMOVE REAR SEAT NO. 3 LEG COVER LH


    1. A01XLLQ

      Detach the 2 claws and remove the cover.

  12. REMOVE REAR SEAT CUSHION INNER HINGE COVER LH


    1. A01XD9JE01
      Text in Illustration
      *1 Guide

      Remove the screw and clip.

    2. Detach the guide and remove the cover.

  13. REMOVE REAR SEAT CUSHION INNER HINGE COVER RH


    1. A01XH0NE01
      Text in Illustration
      *1 Guide

      Remove the screw and clip.

    2. Detach the guide and remove the cover.

  14. REMOVE LOWER SEAT TRACK RAIL LH


    1. A01XIL4

      Remove the 2 bolts and seat track rail.

  15. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01XLIQ

      Detach the 7 clips and remove the board.

  16. REMOVE REAR SEATBACK LOCK HOOK


    1. A01XIVO

      Remove the lock hook.

  17. REMOVE REAR SEAT NO. 1 COVER BEZEL


    1. A01XKDIE01
      Text in Illustration
      *1 Guide

      Remove the 2 screws, detach the guide and remove the bezel.

  18. REMOVE SEATBACK COVER WITH PAD


    1. A01XGAQE01
      Text in Illustration
      *1 Hook

      Detach the hooks.

    2. A01XJI0

      Detach the 8 clips and remove the seatback cover with pad.

  19. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH


    1. A01XHKK

      Remove the hog rings and seatback cover.

  20. REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR


    1. A01XD1SE01
      Text in Illustration
      *1 Tack Pin

      Cut off the tack pins and remove the protector from the seatback pad.

  21. REMOVE NO. 2 SEATBACK COVER


    1. A01XFM8

      Detach the 2 claws and remove the cover.

  22. REMOVE REAR SEAT HEADREST COVER


    1. A01XGAVE01
      Text in Illustration
      *1 Guide

      Remove the 2 screws.

    2. Detach the 2 claws and guide and remove the cover.

  23. REMOVE REAR SEAT HEADREST CABLE


    1. A01XGGAE01
      Text in Illustration
      *1 Cable End
      *2 Clamp

      Detach the 2 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  24. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. A01XMIV

      Remove the 3 nuts and headrest.

  25. REMOVE REAR SEATBACK EDGE PROTECTOR


    1. A01XGGV

      Detach the 4 claws and remove the 2 protectors.

  26. REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH


    1. A01XGJB

      Detach the 4 claws and remove the cover.

  27. REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH


    1. A01XK49E01
      Text in Illustration
      *1 Guide

      Remove the screw.

    2. Detach the guide and 2 claws and remove the cover.

  28. REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. A01XFU9

      Remove the bolt and disconnect the wire harness.

    2. A01XG14

      Using a screwdriver, release the lock lever as shown in the illustration.

    3. A01XJY6

      Retract the seat cushion frame.

    4. Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.

  29. REMOVE REAR SEAT LEG COVER LH


    1. A01XGPOE01
      Text in Illustration
      *1 Hook

      Remove the clip.

    2. Detach the 3 hooks and 5 clips and remove the cover.

  30. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH


    1. A01XFSKE01
      Text in Illustration
      *1 Guide

      Remove the 3 clips.

    2. Detach the 2 claws and 4 guides and remove the 3rd seat link.

  31. REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH


    1. A01XIB1

      Detach the 5 claws and remove the cover.

  32. REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH


    1. A01XJ01E01
      Text in Illustration
      *1 Guide

      Remove the screw.

    2. Detach the guide and 2 claws and remove the cover.

  33. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH


    1. A01XIQ7E01
      Text in Illustration
      *1 Clamp
      *2 Cable End

      Detach the 2 clamps.

    2. Twist the cable end in the direction indicated by the arrow and remove the cable.

  34. REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)


    1. A01XH9CE01
      Text in Illustration
      *1 Cable Tie
      *2 Clamp
      *3 Cable End

      Cut off the 2 cable ties and detach the 3 clamps.

    2. Twist the cable end in the direction indicated by the arrow and remove the cable.

  35. REMOVE REAR SEAT LOCK CONTROL CABLE LH


    1. A01XF28E01
      Text in Illustration
      *1 Cable End
      *2 Clamp

      Detach the 2 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  36. REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side)


    1. A01XDF7E04
      Text in Illustration
      *1 Cable Tie
      *2 Clamp
      *3 Cable End

      Cut off the 2 cable ties and detach the 3 clamps.

    2. Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.

  37. REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH


    1. A01XLFR

      Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.

  38. REMOVE REAR NO. 2 SEAT WIRE LH


    1. A01XF7Y

      Disconnect the connector.

    2. Detach the wire harness clamps and remove the seat wire.

  39. REMOVE NO. 3 SEAT LEG ASSEMBLY LH


    1. A01XME1

      Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.

  40. REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)


    1. A01XMKY

      Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.