REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note


  • Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is replaced with a new one.

    • Initialization (initial position reset) of the fold seat control ECU is performed.


  • Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU Click here.


    • The fold seat control ECU is exchanged with one from another vehicle.

    • The seatback frame and seat leg are inspected.

    • The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

    • The seatback frame or seat leg is replaced.

    • The cable is disconnected from the battery while the seatback or seat cushion is operating.

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. REMOVE DECK BOARD ASSEMBLY


    1. Operate the No. 2 fold seat switch and fold down the 2 seatbacks.

    2. A01XKPT

      Remove the 2 bolts.

    3. Detach the 4 clips and remove the deck board.

  2. REMOVE REAR NO. 4 FLOOR BOARD


    1. A01XCV5E01
      Text in Illustration
      *1 Guide

      Using a moulding remover, detach the clip and 3 claws.

    2. Detach the 2 guides and remove the floor board.

  3. REMOVE REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)


    1. A01XIBOE01
      Text in Illustration
      *1 Guide

      Using a moulding remover, detach the clip and 4 claws.

    2. Detach the 2 guides and remove the floor board.

  4. REMOVE REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)


    1. A01XGFDE01
      Text in Illustration
      *1 Guide

      Using a moulding remover, detach the clip and 3 claws.

    2. Detach the 2 guides and remove the floor board.

  5. REMOVE REAR FLOOR MAT SUPPORT PLATE


    1. Remove the 3 bolts.

      A01XJVEE01
      Text in Illustration
      *1 Guide - -

    2. Detach the 4 claws and 2 guides.

    3. Detach the 5 clips and remove the support plate.

  6. REMOVE DECK BOARD BRACKET REINFORCEMENT


    1. A01XJ25E01
      Text in Illustration
      *1 Hook

      Remove the 2 bolts.

    2. Detach the 2 hooks and reinforcement.

  7. REMOVE NO. 1 DECK BOARD BRACKET LH


    1. A01XJT0

      Remove the 2 bolts and bracket.

  8. REMOVE REAR NO. 2 SEAT ASSEMBLY LH


    1. Operate the No. 2 fold seat switch and raise the 2 seatbacks.

    2. A01XGGR

      Disconnect the connector.

    3. A01XI8P

      Remove the 2 bolts.

    4. A01XE84E03
      Text in Illustration
      *1 Protective Tape
      *2 Guide

      Using a screwdriver, detach the 2 guides and 6 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A01XDHE

      Remove the 2 bolts.

    6. A01XCFQ

      Remove the rear No. 2 seat assembly from the vehicle.

      Note

      Be careful not to damage the vehicle body.

      Tech Tips

      If removing the seat on the RH side with the LH side installed, remove it with the No. 3 rear seat leg cover LH raised as shown in the illustration.