DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off |
- |
| Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off |
- |
| Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off |
- |
| Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off |
- |
| Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off |
- |
| Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off |
- |
| Slide Rear | Sliding switch signal (Rearward) / ON or OFF | ON: Sliding switch (Rearward) on OFF: Sliding switch (Rearward) off |
- |
| Slide Front | Sliding switch signal (Forward) / ON or OFF | ON: Sliding switch (Forward) on OFF: Sliding switch (Forward) off |
- |
| Seat Memory No1 | Seat position memorized with M1 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized |
- |
| Seat Memory No2 | Seat position memorized with M2 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized |
- |
| Ignition Switch | Communication state of ignition switch signal / ON or OFF | ON: Ignition switch ON signal received OFF: Ignition switch ON signal not received |
- |
| P Switch | Shift lever position P signal / ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
- |
| Parking Brake SW | Parking brake switch status / ON or OFF | ON: Parking brake applied OFF: Parking brake released |
- |
| Vehicle Speed | Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for front power seat switch / min: 0 V, max: 19.89 V | Within range of 11 to 14 V | - |
| Slide Position | Seat sliding position / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Reclining Position | Seat reclining position / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Front Vertical Position | Seat front vertical position / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Lifter Position | Seat lifter position / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Slide Pos Mem No1 | Seat sliding position memorized with M1 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Reclining Pos Mem No1 | Seat reclining position memorized with M1 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Frnt Vrtcl Pos Mem No1 | Front vertical position memorized with M1 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Lifter Pos Mem No1 | Lifter position memorized with M1 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Slide Pos Mem No2 | Seat sliding position memorized with M2 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Reclining Pos Mem No2 | Seat reclining position memorized with M2 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Frnt Vrtcl Pos Mem No2 | Front vertical position memorized with M2 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Lifter Pos Mem No2 | Lifter position memorized with M2 switch / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Slide Position Init Flg | Seat sliding limit position memory / ON or OFF | ON: Memorized OFF: Not memorized |
- |
| Slide Position Rear Limit | Seat sliding position / min: 0000, max: 65535 | Within range of 0 to 65535 | - |
| Shift P SW (PMN) | Shift lever position P signal / ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
- |
| Memory Button Buzzer Request | Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG or REG WAIT | OFF: Buzzer does not sound MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan |
- |
| Driver Seat Request Command | Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET | OFF: No instruction MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to recall through memory call function RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seat MEM RET: Request to restore seat to memorized position |
- |
| Driver Seat POS REQ | Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3 | OFF: No operation MEM1: M1 switch operation status MEM2: M2 switch operation status MEM3: Related switch does not exist DRV1: Memory call 1 function operating DRV2: Memory call 2 function operating DRV3: Related function does not exist |
- |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D-Door Courtesy | Front door courtesy light switch assembly signal / ON or OFF | ON: Driver side door open OFF: Driver side door closed |
- |
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: Related switch does not exist |
- |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3 | NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: Related switch does not exist |
- |
| M1 Switch | Seat memory switch M1 signal / ON or OFF | ON: Seat memory switch M1 on OFF: Seat memory switch M1 off |
- |
| M2 Switch | Seat memory switch M2 signal / ON or OFF | ON: Seat memory switch M2 on OFF: Seat memory switch M2 off |
- |
| SET Switch | Seat memory switch SET signal / ON or OFF | ON: Seat memory switch SET on OFF: Seat memory switch SET off |
- |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Reclining | Seat reclining operation | Front / OFF / Rear | - |
| Front Vertical Operation | Seat front vertical operation | Up / OFF / Down | - |
| Lifter Operation | Seat lifter operation | Up / OFF / Down | - |
| Seat Slide Operation | Seat sliding operation | Front / OFF / Rear | - |
| Buzzer | Buzzer operation | ON / OFF | - |