DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Light RH | Turn signal switch (right) status | ON or OFF | ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
| Turn Light LH | Turn signal switch (left) status | ON or OFF | ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
| PCS OFF Switch | Pre-crash safety system on/off status | ON or OFF | ON: Pre-crash safety system on OFF: Pre-crash safety system off |
- |
| PCS Indicator | "Pre-Crash Safety Malfunction Visit Your Dealer" display request signal | ON or OFF | ON: "Pre-Crash Safety Malfunction Visit Your Dealer" display requested OFF: "Pre-Crash Safety Malfunction Visit Your Dealer" display not requested |
- |
| PCS Disabled Indicator | "Pre-Crash Safety Unavailable" display request signal | ON or OFF | ON: "Pre-Crash Safety Unavailable" display requested OFF: "Pre-Crash Safety Unavailable" display not requested |
- |
| Pre-Crash Safety Warning Buz | Pre-crash safety system warning buzzer | Valid or Inval | Valid: Pre-crash safety system warning buzzer operation possible Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Crash Brake | Pre-crash braking function | Valid or Inval | Valid: Pre-crash braking operation possible Inval: Pre-crash braking operation not possible |
- |
| PBA Start | Pre-crash brake assist activation signal | OFF, Standby, Assist Lv1 or Assist Lv2 | OFF: Pre-crash brake assist not operating Standby: Brake pedal not depressed during Pre-crash brake assist operation Assist Lv1: Brake pedal depressed during pre-crash brake assist operation Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation |
Signal status changes when the pre-crash brake assist is activated before a crash(Pre-crash brake will activate only in situations where the driver depresses the brake pedal) |
| Warning Brake | - | - | - | Not applicable to the vehicle |
| Brake Assist Standby | - | - | - | This item is displayed on the GTS but is not used. |
| Pre-Crash Brake Control | Pre-crash braking operational status | ON or OFF | ON: Pre-crash braking operating OFF: Pre-crash braking not operating |
- |
| AVS Start | AVS control activation start | ON or OFF | ON: AVS control activated OFF: AVS control not activated |
- |
| VGRS Start | - | - | - | Not applicable to the vehicle |
| PBA Control | Pre-crash brake assist operational status | Valid or Invalid | Valid: Pre-crash brake assist control operation possible Invalid: Pre-crash brake assist control operation not possible |
- |
| Pre-Crash Safety Brake Ind | Pre-crash safety system alarm warning message status | ON or OFF | ON: Displayed OFF: Not displayed |
"BRAKE!" is displayed |
| PCS Crash Alarm Buzzer | Skid control buzzer assembly status | ON or OFF | ON: Skid control buzzer assembly sounding OFF: Skid control buzzer assembly not sounding |
- |
| Front Radar-Dirt History | Millimeter wave radar sensor assembly dirt history | ON or OFF | ON: History of excessive dirt OFF: No history of excessive dirt |
- |
| Front Radar-Temperature Malfunction History | Millimeter wave radar sensor assembly abnormal temperature history | ON or OFF | ON: History of abnormal temperature OFF: No history of abnormal temperature |
- |
| Front Radar-Low Voltage History | Millimeter wave radar sensor assembly low voltage history | ON or OFF | ON: History of low voltage OFF: No history of low voltage |
- |
| Front Radar-Incorrect Axial Gap (Vertical) History | Millimeter wave radar sensor assembly vertical misalignment history | ON or OFF | ON: History of vertical misalignment OFF: No history of vertical misalignment |
When the "Pre-Crash Safety Unavailable" message is displayed and "History:ON" is output, the millimeter wave radar sensor may be automatically performing beam axis calibration. In this case, perform beam axis adjustment. |
| Front Radar-Incorrect Axial Gap (Horizontal) History | Millimeter wave radar sensor assembly horizontal misalignment history | ON or OFF | ON: History of horizontal misalignment OFF: No history of horizontal misalignment |
- |
| Front Recognition Camera-Blockage History | Forward recognition camera obstruction history | ON or OFF | ON: History of being obstructed OFF: No history of being obstructed |
- |
| Front Recognition Camera-Malfunction History | Forward recognition camera system unavailable history | ON or OFF | ON: History of unavailable OFF: No history of unavailable |
- |
| Driving Support ECU Destination Variation No | Destination country for driving support ECU | Destination Variation No or Not Available | Actual country code | - |
| Control Mode | ECU control mode status | Normal or Check Mode | Normal: Normal operation Check: Operating in Control Mode |
- |
| PCS Operation State Retention Setting | PCS Operation State Retention Setting customize setting | ON or OFF | ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 1 | PCS Alarm Activation Distance Retention Setting 1 customize setting | ON or OFF | ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 2 | PCS Alarm Activation Distance Retention Setting 2 customize setting | ON or OFF | ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| PCS Alarm Activation Distance Retention Setting 3 | PCS Alarm Activation Distance Retention Setting 3 customize setting | ON or OFF | ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
| The Number of DTCs | Number of trouble codes | 0 to 255 | Number of DTCs will be displayed | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Crash Alarm Buzzer | Skid control buzzer assembly | ON / OFF | Test possible with ignition switch ON, vehicle stopped |
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (Stop light switch assembly) | Relay OFF/ON | Stop lights come on |
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Pre-Crash | PCS warning light | ON / OFF | Test possible with ignition switch ON, vehicle stopped |