FRONT SEAT SIDE AIRBAG ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side. (for Manual Seat, Power Seat)

  • The procedure listed below is for the RH side. (for Walk in Seat Type)

PROCEDURE


  1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. Install the front seat side airbag assembly with 2 new nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Attach the 2 clamps.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. Temporarily install the separate type front seatback cover with pad.

    2. Attach the 4 claws to install the 2 front seat headrest supports.

    3. B001ENO

      Install the front seatback cover bracket with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

      • Check that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    4. w/o Seatback Board:


      1. Close the 2 fasteners, and then close the seatback cover.

        B001GUIE01
        Text in Illustration
        *A for Cloth Seat *B for Leather Seat
      2. B001GV0E01
        Text in Illustration
        *1 Hog Ring Pliers

        Using hog ring pliers, install 3 new hog rings.

        Note

        Be sure to securely install the hog rings as shown in the illustration.

    5. w/ Seatback Board:


      1. B001HJ7E01
        Text in Illustration
        *1 Hog Ring Pliers

        Using hog ring pliers, install 5 new hog rings.

        Note


        • Be careful not to damage the separate type front seatback cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      2. Attach the hooks.

      3. Connect the seat heater connector and attach the wire harness clamp.

    6. w/ Seat Heater System:

      Connect the seat heater connector and attach the wire harness clamp.

  3. CONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY


    1. for Manual Seat, Power Seat:


      1. Connect the airbag wire harness.

      2. Attach the fastening tape and close the cover.

      3. Attach the 3 airbag wire harness clamps.

      4. Attach the claw and connect the airbag connector.

    2. for Walk in Seat Type:


      1. Connect the airbag wire harness.

      2. Attach the fastening tape and close the cover.

      3. Attach the 4 airbag wire harness clamps.

      4. Attach the claw and connect the airbag connector.

    3. w/o Seatback Board:


      1. Install the rubber band to the seat cushion spring.

  4. INSTALL FRONT SEATBACK BOARD CLIP (w/ Seatback Board)

    Click here

  5. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

    Click here

  6. INSTALL FRONT SEAT ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here

  7. INSTALL SEAT TRACK COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  8. INSTALL INNER SEAT TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  9. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  10. INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  11. INSTALL SEAT TRACK COVER RH (for Walk in Seat Type)

    Click here

  12. INSTALL INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)

    Click here

  13. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)

    Click here

  14. INSTALL FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)

    Click here

  15. INSTALL FRONT SEAT HEADREST ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  18. INSPECT FRONT SEAT ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here