AIRBAG SYSTEM SRS Warning Light does not Come ON

DESCRIPTION

Refer to "SRS Warning Light Remains ON" Click here.

WIRING DIAGRAM

Refer to "SRS Warning Light Remains ON" Click here.

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

  • After replacing the center airbag sensor, refer to initialization Click here.

PROCEDURE


  1. CHECK BATTERY


    1. Measure the voltage of the battery.

      Standard voltage
      11 to 14 V

    NG

    REPLACE OR RECHARGE BATTERY

    OK

  2. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the combination meter.

      OK
      The connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  3. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)


    1. for 5L-E:


      1. B001DQXC01
        *a

        Front view of wire harness connector

        (to Combination Meter)

        Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      3. Disconnect the G6 connector from the combination meter.

      4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      5. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        G6-28 (IG+) - G6-21 (E2) Ignition switch ON 11 to 14 V
        G6-26 (B) - G6-21 (E2) Always 11 to 14 V

    2. except 5L-E:


      1. B001DQXC02
        *a

        Front view of wire harness connector

        (to Combination Meter)

        Turn the ignition switch off.

      2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

      3. Disconnect the G304 connector from the combination meter.

      4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      5. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        G304-22 (IG+) - G304-20 (E2) Ignition switch ON 11 to 14 V
        G304-21 (B) - G304-20 (E2) Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK SRS WARNING LIGHT (SHORT TO GROUND)


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Connect the connector to the combination meter.

    4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    5. Turn the ignition switch to ON.

    6. Check the SRS warning light condition.

      Note

      Make sure that nobody is in the vehicle.

      OK
      After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.

      Tech Tips

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.


    OK

    REPLACE CENTER AIRBAG SENSOR Click here

    NG

    GO TO METER / GAUGE SYSTEM Click here