AIRBAG SYSTEM, Diagnostic DTC:B1905, B1906, B1907, B1908

DTC Code DTC Name
B1905 Short in P/T Squib (LH) Circuit
B1906 Open in P/T Squib (LH) Circuit
B1907 Short in P/T Squib (LH) Circuit (to Ground)
B1908 Short in P/T Squib (LH) Circuit (to +B)

DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor and front seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1905

One of the following conditions is met:


  • The center airbag sensor detects a line short circuit signal 5 times in the front pretensioner squib LH circuit during the primary check.

  • A front pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Front seat outer belt assembly LH (Front pretensioner squib LH)

  • Center airbag sensor
B1906

One of the following conditions is met:


  • The center airbag sensor detects open circuit signal in the front pretensioner squib LH circuit for 2 seconds.

  • A front pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Front seat outer belt assembly LH (Front pretensioner squib LH)

  • Center airbag sensor
B1907

One of the following conditions is met:


  • The center airbag sensor detects a short circuit to ground signal in the front pretensioner squib LH circuit for 0.5 seconds.

  • A front pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Front seat outer belt assembly LH (Front pretensioner squib LH)

  • Center airbag sensor
B1908

One of the following conditions is met:


  • The center airbag sensor detects a short circuit to B+ signal in the front pretensioner squib LH circuit for 0.5 seconds.

  • A front pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Front seat outer belt assembly LH (Front pretensioner squib LH)

  • Center airbag sensor

WIRING DIAGRAM

B001EMLE04
*a Front Pretensioner Squib LH
*b Center Airbag Sensor

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

  • After replacing the center airbag sensor, refer to initialization Click here.

Tech Tips

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH)


    1. B001EI0C01
      *1 Front Pretensioner Squib LH
      *2 Center Airbag Sensor
      *3 Connector C
      *4 SST
      *a

      Front view of wire harness connector

      (to Front Pretensioner Squib LH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connectors from the front seat outer belt LH.

    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the front seat outer belt LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Clear the DTCs Click here.

    8. Turn the ignition switch off.

    9. Turn the ignition switch to ON, and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1905, B1906, B1907 or B1908 is not output.

      Tech Tips

      Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.

      Result
      Result Proceed to
      OK (for 3 Door) A
      OK (for 5 Door) B
      NG C

    A

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH Click here

    B

    REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH Click here

    C

  2. CHECK CONNECTOR


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect SST from connector C.

    4. B001I5VC40
      *1 Front Pretensioner Squib LH
      *2 Center Airbag Sensor

      Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  3. CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)


    1. B001FRAC27
      *1 Front Pretensioner Squib LH
      *2 No. 2 Floor Wire
      *3 Center Airbag Sensor
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Front Pretensioner Squib LH)

      Disconnect the connectors from the center airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      R2-1 (L+) - Body ground Ignition switch ON Below 1 V
      R2-2 (L-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R2-1 (L+) - R2-2 (L-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B Click here.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R2-1 (L+) - R2-2 (L-) Always 1 MΩ or higher
      R2-1 (L+) - Body ground Always 1 MΩ or higher
      R2-2 (L-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK CENTER AIRBAG SENSOR


    1. B001EHAC40
      *1 Front Pretensioner Squib LH
      *2 Center Airbag Sensor

      Connect the connectors to the front seat outer belt LH and center airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs Click here.

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1905, B1906, B1907 or B1908 is not output.

      Tech Tips

      Codes other than DTC B1905, B1906, B1907 and B1908 may be output at this time, but they are not related to this check.


    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE CENTER AIRBAG SENSOR Click here