CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) Short in CAN Bus Lines

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

  • Short between CAN bus lines

  • ECM

  • Brake actuator assembly (skid control ECU)*1

  • Master cylinder solenoid (skid control ECU)*2

  • Four wheel drive control ECU

  • Network gateway ECU*3

  • Power steering ECU assembly*4

  • Air conditioning amplifier assembly

  • Radio and display receiver assembly*5

  • Spiral cable sub-assembly (steering angle sensor)*4

  • Yaw rate sensor assembly

  • Center airbag sensor assembly

  • Main body ECU (multiplex network body ECU)

  • Combination meter assembly

  • No. 1 junction connector

  • No. 2 junction connector

  • No. 3 junction connector

  • No. 4 junction connector*1

  • No. 5 junction connector*2

WIRING DIAGRAM

A01XJEEE01
A01XE7ME02
A01XF6CE05

CAUTION / NOTICE / HINT

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)


    1. A01XHMNE01
      Text in Illustration
      *a Front view of DLC3

      Disconnect the G94 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G48-6 (CANH) - G48-14 (CANL) Ignition switch off 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

    OK

  3. CONNECT CONNECTOR


    1. Reconnect the G94 No. 3 junction connector.


    NEXT

  4. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)


    1. A01XHMNE01
      Text in Illustration
      *a Front view of DLC3

      Disconnect the G97 No. 1 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G48-6 (CANH) - G48-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)


    1. A01XKEYE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G97-2 (CANH) - G97-13 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

    Note

    For vehicles without a network gateway ECU, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - Air Conditioning Amplifier Assembly)".


    1. A01XMDKE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G97-3 (CANH) - G97-14 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A01XLWRE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G97-4 (CANH) - G97-15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  8. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

    Note

    For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 1 Junction Connector - ECM)".


    1. A01XM3ZE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G97-5 (CANH) - G97-16 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  9. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)


    1. A01XL2FE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 1 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G97-6 (CANH) - G97-17 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK A
      NG (for 1KD-FTV) B
      NG (for 2TR-FE, 5L-E) C

    A

    REPLACE NO. 1 JUNCTION CONNECTOR

    B

    CONNECT CONNECTOR Click here

    C

    CONNECT CONNECTOR Click here

  10. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  11. CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)


    1. A01XJYOE05
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Four Wheel Drive Control ECU)

      Disconnect the G53 four wheel drive control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G53-19 (CANH) - G53-20 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE FOUR WHEEL DRIVE CONTROL ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)

  12. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  13. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)


    1. A01XENEE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Network Gateway ECU)

      Disconnect the G155 network gateway ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G155-16 (CA1H) - G155- 15 (CA1L) Ignition switch off 54 to 69 Ω

    OK

    REPLACE NETWORK GATEWAY ECU Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)

  14. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  15. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. A01XIIME02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Disconnect the G25 air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G25-11 (CANH) - G25-12 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

  16. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  17. CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)


    1. A01XDPDE05
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Steering ECU Assembly)

      Disconnect the G46 power steering ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G46-1 (CANH) - G46-2 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE POWER STEERING ECU ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

  18. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  19. CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    1. A01XHB3E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the G58 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G58-35 (CANH) - G58-36 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

  20. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A01XDH7E01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 4 Junction Connector)

      Disconnect the A72 No. 4 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A72-9 (CANH) - A72-20 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

    OK

  22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)


    1. A01XIDOE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 4 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A72-11 (CANH) - A72-22 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - ECM)


    1. A01XLNQE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 4 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A72-10 (CANH) - A72-21 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK A
      NG (for 2TR-FE) B
      NG (for 5L-E) C

    A

    REPLACE NO. 4 JUNCTION CONNECTOR

    B

    CONNECT CONNECTOR Click here

    C

    CONNECT CONNECTOR Click here

  24. CONNECT CONNECTOR


    1. Reconnect the A72 No. 4 junction connector.


    NEXT

  25. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    1. A01XDAVE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the A6 brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A6-25 (CANH) - A6-14 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

  26. CONNECT CONNECTOR


    1. Reconnect the A72 No. 4 junction connector.


    NEXT

  27. CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    1. A01XLSCE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the G181 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G181-13 (CANH) - G181-14 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

  28. CONNECT CONNECTOR


    1. Reconnect the A72 No. 4 junction connector.


    NEXT

  29. CHECK FOR SHORT IN CAN BUS WIRES (ECM)


    1. A01XH2XE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the G183 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G183-25 (CANH) - G183-31 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

  30. CONNECT CONNECTOR


    1. Reconnect the G97 No. 1 junction connector.


    NEXT

  31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    1. A01XG6QE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Disconnect the G100 No. 2 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G100-1 (CANH) - G100- 12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

    OK

  32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)


    1. A01XHMNE01
      Text in Illustration
      *a Front view of DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G48-6 (CANH) - G48-14 (CANL) Ignition switch off 108 to 132 Ω

    NG

    CONNECT CONNECTOR Click here

    OK

  33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

    Note

    For vehicles without an audio and visual system (for radio and display type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Steering Angle Sensor)".


    1. A01XG13E01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G100-2 (CANH) - G100- 13 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

    Note

    For vehicles without a vehicle stability control system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Yaw Rate Sensor Assembly)".


    1. A01XDMGE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G100-3 (CANH) - G100- 14 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)


    1. A01XLHEE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G100-4 (CANH) - G100- 15 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    1. A01XIHIE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G100-5 (CANH) - G100- 16 (CANL) Ignition switch off 200 Ω or higher

    OK

    REPLACE NO. 2 JUNCTION CONNECTOR

    NG

    CONNECT CONNECTOR Click here

  37. CONNECT CONNECTOR


    1. Reconnect the G100 No. 2 junction connector.


    NEXT

  38. CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)


    1. B001HXXE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the H51 radio and display receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      H51-9 (CANH) - H51-10 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

  39. CONNECT CONNECTOR


    1. Reconnect the G100 No. 2 junction connector.


    NEXT

  40. CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)


    1. A01XLNTE06
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Spiral Cable Sub-assembly [Steering Angle Sensor])

      Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G33-4 (CANH) - G33-3 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

  41. CONNECT CONNECTOR


    1. Reconnect the G100 No. 2 junction connector.


    NEXT

  42. CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)


    1. A01XFP1E05
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Yaw Rate Sensor Assembly)

      Disconnect the G52 yaw rate sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G52-3 (CANH) - G52-2 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE YAW RATE SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)

  43. CONNECT CONNECTOR


    1. Reconnect the G100 No. 2 junction connector.


    NEXT

  44. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)


    1. A01XER9E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Center Airbag Sensor Assembly)

      Disconnect the G1 center airbag sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G1-13 (CANH) - G1-22 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

  45. CONNECT CONNECTOR


    1. Reconnect the G100 No. 2 junction connector.


    NEXT

  46. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    1. A01XLB2E01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Disconnect the G94 No. 3 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G94-1 (CANH) - G94-12 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

    OK

  47. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)


    1. A01XEP9E01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G94-3 (CANH) - G94-14 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01XLZHE01
      Text in Illustration
      *A for 1KD-FTV
      *B for 2TR-FE, 5L-E
      *a

      Rear view of wire harness connector

      (to No. 3 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 1KD-FTV
      Tester Connection Switch Condition Specified Condition
      G94-6 (CANH) - G94-17 (CANL) Ignition switch off 108 to 132 Ω
      for 2TR-FE, 5L-E
      Tester Connection Switch Condition Specified Condition
      G94-2 (CANH) - G94-13 (CANL) Ignition switch off 108 to 132 Ω
      Result
      Result Proceed to
      OK A
      NG (for 2TR-FE, 5L-E) B
      NG (for 1KD-FTV) C

    A

    REPLACE NO. 3 JUNCTION CONNECTOR

    B

    CONNECT CONNECTOR Click here

    C

    CONNECT CONNECTOR Click here

  49. CONNECT CONNECTOR


    1. Reconnect the G94 No. 3 junction connector.


    NEXT

  50. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)


    1. A01XJEFE05
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Main Body ECU [Multiplex Network Body ECU])

      Disconnect the G64 main body ECU (multiplex network body ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G64-14 (CANH) - G64-13 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

  51. CONNECT CONNECTOR


    1. Reconnect the G94 No. 3 junction connector.


    NEXT

  52. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    1. A01XIY0E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the G6 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G6-40 (CANH) - G6-39 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

  53. CONNECT CONNECTOR


    1. Reconnect the G94 No. 3 junction connector.


    NEXT

  54. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)


    1. A01XJMRE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 5 Junction Connector)

      Disconnect the A73 No. 5 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A73-9 (CANH) - A73-20 (CANL) Ignition switch off 108 to 132 Ω

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

    OK

  55. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU)


    1. A01XH2SE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 5 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A73-11 (CANH) - A73-22 (CANL) Ignition switch off 200 Ω or higher

    NG

    CONNECT CONNECTOR Click here

    OK

  56. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    1. A01XKXOE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 5 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A73-10 (CANH) - A73-21 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE NO. 5 JUNCTION CONNECTOR

    NG

    CONNECT CONNECTOR Click here

  57. CONNECT CONNECTOR


    1. Reconnect the A73 No. 5 junction connector.


    NEXT

  58. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)


    1. B001F76E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Master Cylinder Solenoid [Skid Control ECU])

      Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A7-11 (CANH) - A7-25 (CANL) Ignition switch off 54 to 69 Ω

    OK

    REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) Click here

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

  59. CONNECT CONNECTOR


    1. Reconnect the A73 No. 5 junction connector.


    NEXT

  60. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)


    1. A01XIY0E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the G6 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      G6-40 (CANH) - G6-39 (CANL) Ignition switch off 108 to 132 Ω

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)