MAIN BODY ECU INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • A bolt without a torque specification is shown in the standard bolt chart Click here.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL MULTIPLEX NETWORK BODY ECU

    Note


    • Make sure that no foreign objects contact the connecting surfaces.

    • Do not touch the ECU connector.


    1. B001G1JE01
      Text in Illustration
      *1 Housing Sidewall
      *2 Guide Part

      Insert the multiplex network body ECU until it contacts the housing sidewall of the guide part as shown in the illustration.

      Tech Tips

      Be sure to maintain an angle of 20° or more as shown in the illustration.

    2. A01XGRUE01
      Text in Illustration
      *1 Housing Sidewall
      *2 Guide Part
      *3 Junction Block Fuse

      Slide the guide of the multiplex network body ECU along the housing sidewall toward the junction block fuses as shown in the illustration.

    3. A01XINSE04
      Text in Illustration
      *1 Side A

      Slide the multiplex network body ECU so that it contacts side A as shown in the illustration.

      Note

      Do not apply excessive force to the multiplex network body ECU.

    4. A01XM34E01
      Text in Illustration
      *1 Side A Contact Portion

      With the multiplex network body ECU to side A of the junction block (point of rotation), rotate it downward as shown in the illustration.

    5. A01XDQKE01
      Text in Illustration
      *1 Pushing Area

      Press the pushing area until the claw attaches to install the multiplex network body ECU.

      Note


      • Make sure to press only the pushing area.

      • Confirm the engagement of the multiplex network body ECU and junction block by listening for a lock sound.

      • Do not apply excessive force to the multiplex network body ECU.

      Tech Tips

      If a lock sound cannot be heard, visually check the engagement of the lock part. The engagement can also be confirmed if the multiplex network body ECU and junction block are flush.

  2. INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY


    1. A01XG7M

      Attach the claw to install the connector as shown in the illustration.

      Note

      Be sure to connect each connector securely.

    2. A01XE2P

      Attach the 2 claws to lock the connector lock as shown in the illustration.

    3. A01XKJL

      Attach the claw to connect the connector as shown in the illustration.

      Note

      Be sure to connect the connector securely.

    4. Install the driver side junction block assembly with the bolt and 2 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    5. A01XMGZE01

      Connect the connector labeled (1).

      Note

      Be sure to connect each connector securely.

    6. Attach the 2 claws to connect the 2 connectors labeled (2) as shown in the illustration.

      Note

      Be sure to connect each connector securely.

    7. Connect the 3 connectors.

      Note

      Be sure to connect each connector securely.

  3. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

    Click here

  5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    Click here

  6. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

    Click here

  7. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

    Click here

  8. INSTALL INSTRUMENT SIDE PANEL LH

    Click here

  9. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    Click here

  10. INSTALL COWL SIDE TRIM BOARD LH


    1. for 5 Door:

      Install the cowl side trim board LH Click here.

    2. for 3 Door:

      Install the cowl side trim board LH Click here.

  11. INSTALL DOOR SCUFF PLATE ASSEMBLY LH


    1. for 5 Door:

      Install the door scuff plate assembly LH Click here.

    2. for 3 Door:

      Install the door scuff plate assembly LH Click here.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.