BLIND SPOT MONITOR SYSTEM FREEZE FRAME DATA


  1. FREEZE FRAME DATA


    1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.

  2. CHECK FREEZE FRAME DATA


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the blind spot monitor main switch assembly (multi-function switch) on.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

    6. According to the display on the GTS, display the Freeze Frame Data for the selected DTC.

      Blind Spot Monitor Master
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main Switch Blind spot monitor main switch assembly (multi-function switch) / OFF or ON

      ON: Blind spot monitor main switch assembly (multi-function switch) on

      OFF: Blind spot monitor main switch assembly (multi-function switch) off

      		 -
      Warning Indicator Turning on (Master) State of the outer rear view mirror indicator LH turning on / OFF or ON

      • OFF: Any state except "ON" state

      • ON: Either of the following state


        • During initial check

        • Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated

      		 -
      Warning Indicator Flashing (Master) State of the outer rear view mirror indicator LH flashing / OFF or ON

      OFF: Any state except "ON" state

      ON: Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on

      		 -
      Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch assembly (multi-function switch) / OFF or ON

      OFF: Indicator not illuminated

      ON: Indicator illuminated

      		 -
      Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V

      Not illuminated: Below 1 V

      Illuminated: 2.5 to 7.5 V

      		 -
      Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      		 -
      Right Turn SW State (CAN) State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF

      ON: Right side of turn signal light switch on

      OFF: Right side of turn signal light switch off

      		 -
      Left Turn SW State (CAN) State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF

      ON: Left side of turn signal light switch on

      OFF: Left side of turn signal light switch off

      		 -
      Reverse State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -
      Blind Spot Monitor Slave
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Warning Indicator Turning on (Slave) State of the outer rear view mirror indicator RH turning on / OFF or ON

      OFF: Any state except "ON" state

      ON: Either of the following state


      • During initial check

      • Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated

      		 -
      Warning Indicator Flashing (Slave) State of the outer rear view mirror indicator RH flashing / OFF or ON

      OFF: Any state except "ON" state

      ON: Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on

      		 -
      Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON

      OFF: Buzzer not sounding


      • ON: All of the following conditions are met:


        • Not during initial check

        • Vehicle detected in warning area of RCTA

        • Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

        • Shift lever in R

        • No DTC output

      		 -
      Warning Indicator Input Circuit Voltage The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V

      Not illuminated: Below 1 V

      Illuminated: 2.5 to 7.5 V

      		 -
      Warning Indicator Input Circuit Current The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      		 -
      Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V

      Not sounding buzzer: 11 to 14 V

      Sounding buzzer: Alternating between 0 to 14 V

      		 -
      Right Turn SW State (CAN) State of the headlight dimmer switch assembly (right signal light switch) / ON or OFF

      ON: Right side of turn signal light switch on

      OFF: Right side of turn signal light switch off

      		 -
      Left Turn SW State (CAN) State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF

      ON: Left side of turn signal light switch on

      OFF: Left side of turn signal light switch off

      		 -
      Reverse State of the shift position R signal / OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal / -328 to 328 km/h (-204 to 204 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering sensor / Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage / Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state / Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Number of DTC Number of DTC / Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -

  3. CLEAR FREEZE FRAME DATA

    Note

    Clearing the DTCs will also clear the Freeze Frame Data


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the blind spot monitor main switch assembly (multi-function switch) on.

    4. Turn the GTS on.

    5. Clear the DTCs and Freeze Frame Data.