AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Reverse Signal Circuit

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.


WIRING DIAGRAM

B001ETVE02

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).

PROCEDURE


  1. CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. B001HB8

      Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check Click here.

    2. Check that the display changes between ON and OFF according to the shift lever position.

      OK
      Shift Lever Position Display
      R ON
      Except R OFF

      Tech Tips

      This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.


    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

    B001HHJE01
    Text in Illustration
    *a

    Front view of wire harness connector

    (to Radio and Display Receiver Assembly)

    1. Disconnect the radio and display receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      H51-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
      H51-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V
      Result
      Result Proceed to
      OK A
      NG (for Automatic Transmission) B
      NG (for Manual Transmission) C

    A

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    C

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY) Click here

    B

  3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)


    1. Disconnect the H51 radio and display receiver assembly connector.

    2. Disconnect the C40 park/neutral position switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H51-2 (REV) - C40-1 (RL) Always Below 1 Ω
      H51-2 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)


    1. B001HMGE04
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Park/neutral Position Switch Assembly)

      Disconnect the park/neutral position switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C40-2 (RB) - Body ground Ignition switch ON 11 to 14 V
      Result
      Result Proceed to
      OK (for AC60F) A
      OK (for A750F) B
      NG C

    A

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    B

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the H51 radio and display receiver assembly connector.

    2. Disconnect the C41 back-up light switch assembly connector.

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H51-2 (REV) - C41-1 Always Below 1 Ω
      H51-2 (REV) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - BATTERY)


    1. B001GK4E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Back-up Light Switch Assembly)

      Disconnect the back-up light switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C41-2 - Body ground Ignition switch ON 11 to 14 V
      Result
      Result Proceed to
      OK (for R150F) A
      OK (for RA61F) B
      OK (for G52F) C
      NG D

    A

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    B

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    C

    REPLACE BACK-UP LIGHT SWITCH ASSEMBLY Click here

    D

    REPAIR OR REPLACE HARNESS OR CONNECTOR