VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster), Diagnostic DTC:C1422, C1456

DTC Code DTC Name
C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction
C1456 Control Pressure Sensor Zero Point High

DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 Click here.

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.

  • STOP fuse

  • Stop light switch assembly

  • Stop light switch circuit

  • Master cylinder pressure sensor circuit

  • Master cylinder solenoid (Master cylinder pressure sensor)
C1456 When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.

  • STOP fuse

  • Stop light switch assembly

  • Stop light switch circuit

  • Pressure control sensor circuit

  • Master cylinder solenoid (Pressure control sensor)

WIRING DIAGRAM

Refer to DTC C1380 Click here.

CAUTION / NOTICE / HINT

Note


  • When replacing the skid control ECU (master cylinder solenoid), perform calibration Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

When DTC C1425 is output together with DTC C1422 and/or C1456, inspect and repair the trouble areas indicated by DTC C1425 first Click here.

PROCEDURE


  1. READ VALUE USING GTS (STOP LIGHT SW)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    6. Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

      OK
      The GTS displays ON or OFF according to brake pedal operation.

    NG

    INSPECT STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  2. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION


    1. Turn the ignition switch off.

    2. Check the brake pedal height and stop light switch assembly installation Click here.

      OK
      The brake pedal height and stop light switch assembly installation are normal.

    NG

    ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  3. RECONFIRM DTC


    1. Clear the DTC Click here.

    2. Start the engine.

    3. Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).

    4. Check if the same DTC is output Click here.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output (for LHD) B
      DTC is output (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here

  4. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Remove the stop light switch assembly Click here.

    2. Inspect the stop light switch assembly Click here.

      OK
      The stop light switch assembly is normal.

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    1. Turn the ignition switch off.

    2. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

    3. B001CTYC01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU (Master Cylinder Solenoid))

      Measure the resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
      Brake pedal released Below 1.5 V
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE MASTER CYLINDER SOLENOID Click here

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR