VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster), Diagnostic DTC:C1379

DTC Code DTC Name
C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC)

DESCRIPTION

w/ Downhill Assist Control:

DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.

w/ Crawl Control:

DTC C1379 is cleared when the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) send a crawl control operation signal or when test mode ends.

DTC Code DTC Detection Condition Trouble Area
C1379 Stored only during test mode.

  • Downhill assist control switch (w/ Downhill Assist Control)

  • Crawl on/off switch (Center cluster module switch) (w/ Crawl Control)

  • Crawl speed selector (Center cluster module switch) (w/ Crawl Control)

  • Harness or connector

  • Skid control ECU (Master cylinder solenoid)

WIRING DIAGRAM

B001D36E10
w/ Downhill Assist Control
*a Downhill Assist Control Switch
*b Skid Control ECU (Master Cylinder Solenoid)
A01XM1SE04

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (master cylinder solenoid), perform calibration Click here.

PROCEDURE


  1. CONFIRM VEHICLE SPECIFICATIONS


    1. Confirm the vehicle specifications.

      Result
      Result Proceed to
      w/ Downhill Assist Control A
      w/ Crawl Control B

    B

    CHECK CAN BUS Click here

    A

  2. READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    6. Check the Data List for proper functioning of the downhill assist control switch.

      ABS/VSC/TRC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Downhill Assist Control SW Downhill assist control switch / ON or OFF

      ON: Downhill assist control on

      OFF: Downhill assist control off

      		 -
      OK
      The GTS displays ON or OFF according to downhill assist control switch operation.

    NG

    INSPECT DOWNHILL ASSIST CONTROL SWITCH Click here

    OK

  3. CHECK TEST MODE DTC


    1. Perform the downhill assist control switch check in the Test Mode Procedure Click here.

      OK
      Test mode DTC C1379 is cleared.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here

  4. INSPECT DOWNHILL ASSIST CONTROL SWITCH


    1. Remove the downhill assist control switch Click here.

    2. A01XMFXE02
      Text in Illustration
      *a

      Component without harness connected

      (Downhill Assist Control Switch)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 4 Not pushed in 10 kΩ or higher
      Pushed in Below 1 Ω

    NG

    REPLACE DOWNHILL ASSIST CONTROL SWITCH Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)


    1. Disconnect the A7 skid control ECU (master cylinder solenoid) connector.

    2. Disconnect the G158 downhill assist control switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A7-44 (HDCS) - G158-4 Always Below 1 Ω
      A7-44 (HDCS) or G158-4 - Body ground Always 10 kΩ or higher
      G158-1 - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    A

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here

  6. CHECK CAN BUS


    1. Check that there are no problems with the CAN communication system (for LHD: See page , for RHD: Click here.

      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    C

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    A

  7. READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / D-SEAT SW / Data List.

    6. Check the Data List for proper functioning of the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch).

      D-SEAT SW
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Crawl Control Main Switch Crawl on/off switch/ ON or OFF

      ON: Switch on

      OFF: Switch off

      		 -
      Dial Switch Signal 1 Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF Switches between ON and OFF according to the ON/OFF Combination Chart below. -
      Dial Switch Signal 2 Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF -
      Dial Switch Signal 3 Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF -

      1. A01XJ9CE06
        Text in Illustration
        *1 Center Cluster Module Switch
        *2 Crawl On/Off Switch
        *3 Multi-terrain Select Switch
        *4 Crawl Speed Selector/Multi-terrain Select Road Mode Selector
        *a Low/MUD & SAND
        *b Medium-low/LOOSE ROCK
        *c Medium/MOGUL
        *d Medium-high/ROCK & DIRT
        *e High/ROCK

        Operate the crawl speed selector/multi-terrain select road mode selector and check that "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3" in the Data List display ON and OFF according to the chart shown below.

        ON/OFF Combination Chart for "Dial Switch Signal 1", "Dial Switch Signal 2" and "Dial Switch Signal 3"
        Crawl Speed Selector Position/Multi-terrain Select Road Mode Selector Position Low/MUD & SAND Medium-low/LOOSE ROCK Medium/MOGUL Medium-high/ROCK & DIRT High/ROCK
        Data List Display Dial Switch Signal 1 ON ON OFF OFF OFF
        Dial Switch Signal 2 ON OFF OFF OFF ON
        Dial Switch Signal 3 OFF OFF OFF ON ON
        OK
        The GTS display changes according to crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) operation.

    NG

    CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU) Click here

    OK

  8. CHECK TEST MODE DTC


    1. Perform the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) check in the Test Mode Procedure Click here.

      OK
      Test mode DTC C1379 is cleared.
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE MASTER CYLINDER SOLENOID Click here

    C

    REPLACE MASTER CYLINDER SOLENOID Click here

  9. CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)


    1. Disconnect the G156 center cluster module switch connector.

    2. Disconnect the G162 driving support switch control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G162-6 (CRWL) - G156-21 (FRB) Always Below 1 Ω
      G162-4 (MOD1) - G156-17 (ECU) Always Below 1 Ω
      G162-11 (MOD3) - G156-19 (DN) Always Below 1 Ω
      G162-2 (MOD2) - G156-18 (UP) Always Below 1 Ω
      G156-24 (E) - Body ground Always Below 1 Ω
      G162-6 (CRWL) or G156-21 (FRB) - Body ground Always 10 kΩ or higher
      G162-4 (MOD1) or G156-17 (ECU) - Body ground Always 10 kΩ or higher
      G162-11 (MOD3) or G156-19 (DN) - Body ground Always 10 kΩ or higher
      G162-2 (MOD2) or G156-18 (UP) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT CENTER CLUSTER MODULE SWITCH


    1. Remove the center cluster module switch Click here.

    2. Inspect the crawl on/off switch (center cluster module switch) and crawl speed selector (center cluster module switch) Click here.


    OK

    REPLACE DRIVING SUPPORT SWITCH CONTROL ECU Click here

    NG

    REPLACE CENTER CLUSTER MODULE SWITCH Click here