AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV) Transmission Control Switch Circuit

DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "5" (S5 range) using the transmission control switch.

Shifting to "+" once raises the shift range by one, and shifting to "-" once lowers the shift range by one.

WIRING DIAGRAM

B001HEWE11

PROCEDURE


  1. INSPECT TRANSMISSION CONTROL SWITCH


    1. B001DSSE49
      Text in Illustration
      *a

      Component without harness connected

      (Transmission Control Switch)

      Disconnect the G47 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
      2 (SFTU) - 5 (E)

      Shift lever held in "+"

      (Up-shift)

      		 Below 1 Ω
      1 (SFTD) - 5 (E)

      Shift lever held in "-"

      (Down-shift)

      		 Below 1 Ω
      3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher
      2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
      1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher

    NG

    REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)


    1. B001I2FE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Transmission Control Switch)

      Disconnect the G47 transmission control switch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G47-3 (IG) - Body ground Ignition switch ON 11 to 14 V
      G47-3 (IG) - Body ground Ignition switch off Below 1 V

    3. Turn the ignition switch off.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G47-5 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - TCM)


    1. B001E9XE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to TCM)

      Disconnect the G70 TCM connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G70-15 (S) - Body ground

      • Ignition switch ON

      • Shift lever in S, "+" or "-"

      		 11 to 14 V
      G70-15 (S) - Body ground

      • Ignition switch ON

      • Shift lever not in S, "+" or "-"

      		 Below 1 V

    3. Turn the ignition switch off.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G70-22 (SFTU) - Body ground

      Shift lever held in "+"

      (Up-shift)

      		 Below 1 Ω
      G70-23 (SFTD) - Body ground

      Shift lever held in "-"

      (Down-shift)

      		 Below 1 Ω
      G70-22 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
      G70-23 (SFTD) - Body ground Shift lever in S 10 kΩ or higher

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR