AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV), Diagnostic DTC:P0976, P0977

DTC Code DTC Name
P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)
P0977 Shift Solenoid "B" Control Circuit High (Shift Solenoid Valve S2)

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly. In the case of an open or short circuit, the TCM stops sending current to the circuit. For details, refer to the fail-safe chart Click here.

DTC Code DTC Detection Condition Trouble Area
P0976 TCM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection logic).

  • Short in shift solenoid valve S2 circuit

  • Shift solenoid valve S2

  • TCM
P0977 TCM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip detection logic).

  • Open in shift solenoid valve S2 circuit

  • Shift solenoid valve S2

  • TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S2 is on, if its resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S2 circuit.

When shift solenoid valve S2 is off, if its resistance is 100 kΩ or higher, the TCM determines there is an open in the shift solenoid valve S2 circuit Click here.

WIRING DIAGRAM

A01XKWEE40
*1 Shift Solenoid Valve S2
*2 Transmission Wire

CAUTION / NOTICE / HINT

Tech Tips

Shift solenoid valve S2 is turned ON/OFF normally when the shift lever is in D.

TCM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve S2 OFF ON ON OFF OFF

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE S2)


    1. A01XCK1E05
      Text in Illustration
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the C30 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      15 (S2) - Body ground 20°C (68°F) 11 to 15 Ω

    NG

    INSPECT SHIFT SOLENOID VALVE S2 Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    1. A01XHY8E02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to TCM)

      Disconnect the G69 TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G69-17 (S2) - Body ground 20°C (68°F) 11 to 15 Ω

    OK

    REPLACE TCM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. INSPECT SHIFT SOLENOID VALVE S2


    1. B001E7ZE01
      Text in Illustration
      *a

      Component without harness connected

      (Shift Solenoid Valve S2)

      Remove shift solenoid valve S2.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω

    3. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition

      • Battery positive (+) → Shift solenoid valve S2 connector

      • Battery negative (-) → Shift solenoid valve S2 body

      		 Valve moves and makes an operating noise

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE SHIFT SOLENOID VALVE S2 Click here