TRANSMITTER BATTERY(w/o Entry and Start System) REPLACEMENT

CAUTION / NOTICE / HINT

Note

Take extra care when handling these precision electronic components.

PROCEDURE


  1. REMOVE TRANSMITTER HOUSING COVER (except Separate Type)


    1. B001GPBC04
      *1 Housing Cover
      B001CE2 Protective Tape

      Using a screwdriver with its tip wrapped in protective tape, pry apart the transmitter housing cover.

      Note


      • Do not use excessive force when prying apart the housing cover.

      • Remove the transmitter housing cover while the switches face downward to prevent the switch knob from falling.

  2. REMOVE DOOR CONTROL TRANSMITTER MODULE SET (except Separate Type)


    1. B001D24

      Remove the door control transmitter module set.

      Note

      When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.

  3. REMOVE TRANSMITTER BATTERY (except Separate Type)


    1. B001FM9

      Twist a coin in the direction of the arrow in the illustration and detach the 7 claws to remove the transmitter battery cover.

      Note

      When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

    2. B001DD0

      Remove the transmitter battery (lithium battery: CR2016).

      Note


      • When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

      • Do not push the terminals with your finger.

      • Do not forcibly pry up the transmitter battery as the terminals may be damaged.

      • Do not touch the transmitter battery with wet hands. Water may cause it to rust.

      • Do not touch or move any components inside the transmitter as this may interfere with its proper operation.

  4. INSTALL TRANSMITTER BATTERY (except Separate Type)


    1. B001ELF

      Install a new transmitter battery (lithium battery: CR2016) with the positive (+) side up, as shown in the illustration.

      Note


      • When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

      • Make sure that the positive (+) side and the negative (-) side of the transmitter battery are correctly matched with the transmitter terminals.

      • Do not bend the transmitter battery electrode during installation.

      • Keep the inside of the transmitter battery case free of dust and oil.

    2. B001CU0

      Attach the 7 claws to install the transmitter battery cover.

  5. INSTALL DOOR CONTROL TRANSMITTER MODULE SET (except Separate Type)


    1. B001H7H

      Install the door control transmitter module set to the transmitter housing case from directly above.

      Note


      • When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

      • The switches may not be able to operate normally when the door control transmitter module set is installed with keeping its rubber projections bent.

  6. INSTALL TRANSMITTER HOUSING COVER (except Separate Type)


    1. B001CV3

      Install the transmitter housing cover onto the transmitter housing case securely.

  7. REMOVE TRANSMITTER BATTERY (for Separate Type)


    1. B001CI8

      Twist a coin in the direction of the arrow in the illustration and remove the transmitter housing cover.

      Note

      When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

    2. B001CC6

      Remove the transmitter battery (lithium battery: CR2032).

      Note


      • Do not push the terminals with your finger.

      • Do not forcibly pry up the transmitter battery as the terminals may be damaged.

      • Do not touch the transmitter battery with wet hands. Water may cause it to rust.

      • Do not touch or move any components inside the transmitter as this may interfere with proper operation.

  8. INSTALL TRANSMITTER BATTERY (for Separate Type)


    1. B001CC6

      Install a new transmitter battery (lithium battery: CR2032) with the positive (+) side up, as shown in the illustration.

      Note


      • When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.

      • Make sure that the positive (+) side and the negative (-) side of the transmitter battery are correctly matched with the transmitter terminals.

      • Do not bend the transmitter battery electrode during installation.

      • Keep the inside of the transmitter housing case free of dust and oil.

    2. Install the transmitter housing cover.

    3. Press one of the transmitter switches and check that the LED illuminates.